1.客户端发送request
2.服务端返回16字节的服务端AuthenticatorChallenge(随机数)
3.客户端生成16字节的客户端peerChallenge(随机数)
4.客户端计算根据password计算NTpasswordHash,并使用peerChallenge,AuthenticatorChallenge,NTpasswordHash计算NTresponse,计算方法参考RFC2759
5.客户端将NTresponse发送给服务端
6.服务端按照相同方法计算NTresponse,与客户端计算的NTresponse对比.通过后计算AuthenticatorResponse,发送验证成功包.
如下为RFC2759,其中包含所有计算过程用到的函数的伪码,以及一个计算例子
[Docs] [txt|pdf] [draft-ietf-pppext...] [Diff1] [Diff2] [Errata]
INFORMATIONAL
Errata Exist
Network Working Group G. Zorn
Request for Comments: 2759 Microsoft Corporation
Category: Informational January 2000
Microsoft PPP CHAP Extensions, Version 2
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2000). All Rights Reserved.
Abstract
The Point-to-Point Protocol (PPP) [1] provides a standard method for
transporting multi-protocol datagrams over point-to-point links. PPP
defines an extensible Link Control Protocol and a family of Network
Control Protocols (NCPs) for establishing and configuring different
network-layer protocols.
This document describes version two of Microsoft's PPP CHAP dialect
(MS-CHAP-V2). MS-CHAP-V2 is similar to, but incompatible with, MS-
CHAP version one (MS-CHAP-V1, described in [9]). In particular,
certain protocol fields have been deleted or reused but with
different semantics. In addition, MS-CHAP-V2 features mutual
authentication.
The algorithms used in the generation of various MS-CHAP-V2 protocol
fields are described in section 8. Negotiation and hash generation
examples are provided in section 9.
Specification of Requirements
In this document, the key words "MAY", "MUST, "MUST NOT", "optional",
"recommended", "SHOULD", and "SHOULD NOT" are to be interpreted as
described in [3].
Zorn Informational [Page 1]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. LCP Configuration . . . . . . . . . . . . . . . . . . . . . . . 3
3. Challenge Packet . . . . . . . . . . . . . . . . . . . . . . . 3
4. Response Packet . . . . . . . . . . . . . . . . . . . . . . . . 4
5. Success Packet . . . . . . . . . . . . . . . . . . . . . . . . 4
6. Failure Packet . . . . . . . . . . . . . . . . . . . . . . . . 5
7. Change-Password Packet . . . . . . . . . . . . . . . . . . . . 6
8. Pseudocode . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8.1. GenerateNTResponse() . . . . . . . . . . . . . . . . . . . . 7
8.2. ChallengeHash() . . . . . . . . . . . . . . . . . . . . . . . 8
8.3. NtPasswordHash() . . . . . . . . . . . . . . . . . . . . . . 9
8.4. HashNtPasswordHash() . . . . . . . . . . . . . . . . . . . . 9
8.5. ChallengeResponse() . . . . . . . . . . . . . . . . . . . . . 9
8.6. DesEncrypt() . . . . . . . . . . . . . . . . . . . . . . . . 10
8.7. GenerateAuthenticatorResponse() . . . . . . . . . . . . . . . 10
8.8. CheckAuthenticatorResponse() . . . . . . . . . . . . . . . . 12
8.9. NewPasswordEncryptedWithOldNtPasswordHash() . . . . . . . . . 12
8.10. EncryptPwBlockWithPasswordHash() . . . . . . . . . . . . . . 13
8.11. Rc4Encrypt() . . . . . . . . . . . . . . . . . . . . . . . . 13
8.12. OldNtPasswordHashEncryptedWithNewNtPasswordHash() . . . . . 14
8.13. NtPasswordHashEncryptedWithBlock() . . . . . . . . . . . . . 14
9. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9.1. Negotiation Examples . . . . . . . . . . . . . . . . . . . . 14
9.1.1. Successful authentication . . . . . . . . . . . . . . . . . 15
9.1.2. Authenticator authentication failure . . . . . . . . . . . 15
9.1.3. Failed authentication with no retry allowed . . . . . . . . 15
9.1.4. Successful authentication after retry . . . . . . . . . . . 15
9.1.5. Failed hack attack with 3 attempts allowed . . . . . . . . 15
9.1.6. Successful authentication with password change . . . . . . 16
9.1.7. Successful authentication with retry and password change. . 16
9.2. Hash Example . . . . . . . . . . . . . . . . . . . . . . . . 16
9.3. Example of DES Key Generation . . . . . . . . . . . . . . . . 17
10. Security Considerations . . . . . . . . . . . . . . . . . . . 17
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 18
12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 19
13. Author's Address . . . . . . . . . . . . . . . . . . . . . . . 19
14. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 20
Zorn Informational [Page 2]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
1. Introduction
Where possible, MS-CHAP-V2 is consistent with both MS-CHAP-V1 and
standard CHAP. Briefly, the differences between MS-CHAP-V2 and MS-
CHAP-V1 are:
* MS-CHAP-V2 is enabled by negotiating CHAP Algorithm 0x81 in LCP
option 3, Authentication Protocol.
* MS-CHAP-V2 provides mutual authentication between peers by
piggybacking a peer challenge on the Response packet and an
authenticator response on the Success packet.
* The calculation of the "Windows NT compatible challenge response"
sub-field in the Response packet has been changed to include the
peer challenge and the user name.
* In MS-CHAP-V1, the "LAN Manager compatible challenge response"
sub-field was always sent in the Response packet. This field has
been replaced in MS-CHAP-V2 by the Peer-Challenge field.
* The format of the Message field in the Failure packet has been
changed.
* The Change Password (version 1) and Change Password (version 2)
packets are no longer supported. They have been replaced with a
single Change-Password packet.
2. LCP Configuration
The LCP configuration for MS-CHAP-V2 is identical to that for
standard CHAP, except that the Algorithm field has value 0x81, rather
than the MD5 value 0x05. PPP implementations which do not support
MS-CHAP-V2, but correctly implement LCP Config-Rej, should have no
problem dealing with this non-standard option.
3. Challenge Packet
The MS-CHAP-V2 Challenge packet is identical in format to the
standard CHAP Challenge packet.
MS-CHAP-V2 authenticators send an 16-octet challenge Value field.
Peers need not duplicate Microsoft's algorithm for selecting the 16-
octet value, but the standard guidelines on randomness [1,2,7] SHOULD
be observed.
Microsoft authenticators do not currently provide information in the
Name field. This may change in the future.
Zorn Informational [Page 3]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
4. Response Packet
The MS-CHAP-V2 Response packet is identical in format to the standard
CHAP Response packet. However, the Value field is sub-formatted
differently as follows:
16 octets: Peer-Challenge
8 octets: Reserved, must be zero
24 octets: NT-Response
1 octet : Flags
The Peer-Challenge field is a 16-octet random number. As the name
implies, it is generated by the peer and is used in the calculation
of the NT-Response field, below. Peers need not duplicate
Microsoft's algorithm for selecting the 16-octet value, but the
standard guidelines on randomness [1,2,7] SHOULD be observed.
The NT-Response field is an encoded function of the password, the
user name, the contents of the Peer-Challenge field and the received
challenge as output by the routine GenerateNTResponse() (see section
8.1, below). The Windows NT password is a string of 0 to
(theoretically) 256 case-sensitive Unicode [8] characters. Current
versions of Windows NT limit passwords to 14 characters, mainly for
compatibility reasons; this may change in the future. When computing
the NT-Response field contents, only the user name is used, without
any associated Windows NT domain name. This is true regardless of
whether a Windows NT domain name is present in the Name field (see
below).
The Flag field is reserved for future use and MUST be zero.
The Name field is a string of 0 to (theoretically) 256 case-sensitive
ASCII characters which identifies the peer's user account name. The
Windows NT domain name may prefix the user's account name (e.g.
"BIGCO\johndoe" where "BIGCO" is a Windows NT domain containing the
user account "johndoe"). If a domain is not provided, the backslash
should also be omitted, (e.g. "johndoe").
5. Success Packet
The Success packet is identical in format to the standard CHAP
Success packet. However, the Message field contains a 42-octet
authenticator response string and a printable message. The format of
the message field is illustrated below.
"S=<auth_string> M=<message>"
Zorn Informational [Page 4]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
The <auth_string> quantity is a 20 octet number encoded in ASCII as
40 hexadecimal digits. The hexadecimal digits A-F (if present) MUST
be uppercase. This number is derived from the challenge from the
Challenge packet, the Peer-Challenge and NT-Response fields from the
Response packet, and the peer password as output by the routine
GenerateAuthenticatorResponse() (see section 8.7, below). The
authenticating peer MUST verify the authenticator response when a
Success packet is received. The method for verifying the
authenticator is described in section 8.8, below. If the
authenticator response is either missing or incorrect, the peer MUST
end the session.
The <message> quantity is human-readable text in the appropriate
charset and language [12].
6. Failure Packet
The Failure packet is identical in format to the standard CHAP
Failure packet. There is, however, formatted text stored in the
Message field which, contrary to the standard CHAP rules, does affect
the operation of the protocol. The Message field format is:
"E=eeeeeeeeee R=r C=cccccccccccccccccccccccccccccccc V=vvvvvvvvvv
M=<msg>"
where
The "eeeeeeeeee" is the ASCII representation of a decimal error
code (need not be 10 digits) corresponding to one of those listed
below, though implementations should deal with codes not on this
list gracefully.
646 ERROR_RESTRICTED_LOGON_HOURS
647 ERROR_ACCT_DISABLED
648 ERROR_PASSWD_EXPIRED
649 ERROR_NO_DIALIN_PERMISSION
691 ERROR_AUTHENTICATION_FAILURE
709 ERROR_CHANGING_PASSWORD
The "r" is an ASCII flag set to '1' if a retry is allowed, and '0'
if not. When the authenticator sets this flag to '1' it disables
short timeouts, expecting the peer to prompt the user for new
credentials and resubmit the response.
The "cccccccccccccccccccccccccccccccc" is the ASCII representation
of a hexadecimal challenge value. This field MUST be exactly 32
octets long and MUST be present.
Zorn Informational [Page 5]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
The "vvvvvvvvvv" is the ASCII representation of a decimal version
code (need not be 10 digits) indicating the password changing
protocol version supported on the server. For MS-CHAP-V2, this
value SHOULD always be 3.
<msg> is human-readable text in the appropriate charset and
language [12].
7. Change-Password Packet
The Change-Password packet does not appear in either standard CHAP or
MS-CHAP-V1. It allows the peer to change the password on the account
specified in the preceding Response packet. The Change-Password
packet should be sent only if the authenticator reports
ERROR_PASSWD_EXPIRED (E=648) in the Message field of the Failure
packet.
This packet type is supported by recent versions of Windows NT 4.0,
Windows 95 and Windows 98. It is not supported by Windows NT 3.5,
Windows NT 3.51, or early versions of Windows NT 4.0, Windows 95 and
Windows 98.
The format of this packet is as follows:
1 octet : Code
1 octet : Identifier
2 octets : Length
516 octets : Encrypted-Password
16 octets : Encrypted-Hash
16 octets : Peer-Challenge
8 octets : Reserved
24 octets : NT-Response
2-octet : Flags
Code
7
Identifier
The Identifier field is one octet and aids in matching requests
and replies. The value is the Identifier of the received Failure
packet to which this packet responds plus 1.
Length
586
Zorn Informational [Page 6]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
Encrypted-Password
This field contains the PWBLOCK form of the new Windows NT
password encrypted with the old Windows NT password hash, as
output by the NewPasswordEncryptedWithOldNtPasswordHash() routine
(see section 8.9, below).
Encrypted-Hash
This field contains the old Windows NT password hash encrypted
with the new Windows NT password hash, as output by the
OldNtPasswordHashEncryptedWithNewNtPasswordHash() routine (see
section 8.12, below).
Peer-Challenge
A 16-octet random quantity, as described in the Response packet
description.
Reserved
8 octets, must be zero.
NT-Response
The NT-Response field (as described in the Response packet
description), but calculated on the new password and the challenge
received in the Failure packet.
Flags
This field is two octets in length. It is a bit field of option
flags where 0 is the least significant bit of the 16-bit quantity.
The format of this field is illustrated in the following diagram:
1
5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Bits 0-15
Reserved, always clear (0).
8. Pseudocode
The routines mentioned in the text above are described in pseudocode
in the following sections.
8.1. GenerateNTResponse()
GenerateNTResponse(
IN 16-octet AuthenticatorChallenge,
IN 16-octet PeerChallenge,
Zorn Informational [Page 7]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
IN 0-to-256-char UserName,
IN 0-to-256-unicode-char Password,
OUT 24-octet Response )
{
8-octet Challenge
16-octet PasswordHash
ChallengeHash( PeerChallenge, AuthenticatorChallenge, UserName,
giving Challenge)
NtPasswordHash( Password, giving PasswordHash )
ChallengeResponse( Challenge, PasswordHash, giving Response )
}
8.2. ChallengeHash()
ChallengeHash(
IN 16-octet PeerChallenge,
IN 16-octet AuthenticatorChallenge,
IN 0-to-256-char UserName,
OUT 8-octet Challenge
{
/*
* SHAInit(), SHAUpdate() and SHAFinal() functions are an
* implementation of Secure Hash Algorithm (SHA-1) [11]. These are
* available in public domain or can be licensed from
* RSA Data Security, Inc.
*/
SHAInit(Context)
SHAUpdate(Context, PeerChallenge, 16)
SHAUpdate(Context, AuthenticatorChallenge, 16)
/*
* Only the user name (as presented by the peer and
* excluding any prepended domain name)
* is used as input to SHAUpdate().
*/
SHAUpdate(Context, UserName, strlen(Username))
SHAFinal(Context, Digest)
memcpy(Challenge, Digest, 8)
}
Zorn Informational [Page 8]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
8.3. NtPasswordHash()
NtPasswordHash(
IN 0-to-256-unicode-char Password,
OUT 16-octet PasswordHash )
{
/*
* Use the MD4 algorithm [5] to irreversibly hash Password
* into PasswordHash. Only the password is hashed without
* including any terminating 0.
*/
}
8.4. HashNtPasswordHash()
HashNtPasswordHash(
IN 16-octet PasswordHash,
OUT 16-octet PasswordHashHash )
{
/*
* Use the MD4 algorithm [5] to irreversibly hash
* PasswordHash into PasswordHashHash.
*/
}
8.5. ChallengeResponse()
ChallengeResponse(
IN 8-octet Challenge,
IN 16-octet PasswordHash,
OUT 24-octet Response )
{
Set ZPasswordHash to PasswordHash zero-padded to 21 octets
DesEncrypt( Challenge,
1st 7-octets of ZPasswordHash,
giving 1st 8-octets of Response )
DesEncrypt( Challenge,
2nd 7-octets of ZPasswordHash,
giving 2nd 8-octets of Response )
DesEncrypt( Challenge,
3rd 7-octets of ZPasswordHash,
giving 3rd 8-octets of Response )
}
Zorn Informational [Page 9]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
8.6. DesEncrypt()
DesEncrypt(
IN 8-octet Clear,
IN 7-octet Key,
OUT 8-octet Cypher )
{
/*
* Use the DES encryption algorithm [4] in ECB mode [10]
* to encrypt Clear into Cypher such that Cypher can
* only be decrypted back to Clear by providing Key.
* Note that the DES algorithm takes as input a 64-bit
* stream where the 8th, 16th, 24th, etc. bits are
* parity bits ignored by the encrypting algorithm.
* Unless you write your own DES to accept 56-bit input
* without parity, you will need to insert the parity bits
* yourself.
*/
}
8.7. GenerateAuthenticatorResponse()
GenerateAuthenticatorResponse(
IN 0-to-256-unicode-char Password,
IN 24-octet NT-Response,
IN 16-octet PeerChallenge,
IN 16-octet AuthenticatorChallenge,
IN 0-to-256-char UserName,
OUT 42-octet AuthenticatorResponse )
{
16-octet PasswordHash
16-octet PasswordHashHash
8-octet Challenge
/*
* "Magic" constants used in response generation
*/
Magic1[39] =
{0x4D, 0x61, 0x67, 0x69, 0x63, 0x20, 0x73, 0x65, 0x72, 0x76,
0x65, 0x72, 0x20, 0x74, 0x6F, 0x20, 0x63, 0x6C, 0x69, 0x65,
0x6E, 0x74, 0x20, 0x73, 0x69, 0x67, 0x6E, 0x69, 0x6E, 0x67,
0x20, 0x63, 0x6F, 0x6E, 0x73, 0x74, 0x61, 0x6E, 0x74};
Zorn Informational [Page 10]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
Magic2[41] =
{0x50, 0x61, 0x64, 0x20, 0x74, 0x6F, 0x20, 0x6D, 0x61, 0x6B,
0x65, 0x20, 0x69, 0x74, 0x20, 0x64, 0x6F, 0x20, 0x6D, 0x6F,
0x72, 0x65, 0x20, 0x74, 0x68, 0x61, 0x6E, 0x20, 0x6F, 0x6E,
0x65, 0x20, 0x69, 0x74, 0x65, 0x72, 0x61, 0x74, 0x69, 0x6F,
0x6E};
/*
* Hash the password with MD4
*/
NtPasswordHash( Password, giving PasswordHash )
/*
* Now hash the hash
*/
HashNtPasswordHash( PasswordHash, giving PasswordHashHash)
SHAInit(Context)
SHAUpdate(Context, PasswordHashHash, 16)
SHAUpdate(Context, NTResponse, 24)
SHAUpdate(Context, Magic1, 39)
SHAFinal(Context, Digest)
ChallengeHash( PeerChallenge, AuthenticatorChallenge, UserName,
giving Challenge)
SHAInit(Context)
SHAUpdate(Context, Digest, 20)
SHAUpdate(Context, Challenge, 8)
SHAUpdate(Context, Magic2, 41)
SHAFinal(Context, Digest)
/*
* Encode the value of 'Digest' as "S=" followed by
* 40 ASCII hexadecimal digits and return it in
* AuthenticatorResponse.
* For example,
* "S=0123456789ABCDEF0123456789ABCDEF01234567"
*/
}
Zorn Informational [Page 11]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
8.8. CheckAuthenticatorResponse()
CheckAuthenticatorResponse(
IN 0-to-256-unicode-char Password,
IN 24-octet NtResponse,
IN 16-octet PeerChallenge,
IN 16-octet AuthenticatorChallenge,
IN 0-to-256-char UserName,
IN 42-octet ReceivedResponse,
OUT Boolean ResponseOK )
{
20-octet MyResponse
set ResponseOK = FALSE
GenerateAuthenticatorResponse( Password, NtResponse, PeerChallenge,
AuthenticatorChallenge, UserName,
giving MyResponse)
if (MyResponse = ReceivedResponse) then set ResponseOK = TRUE
return ResponseOK
}
8.9. NewPasswordEncryptedWithOldNtPasswordHash()
datatype-PWBLOCK
{
256-unicode-char Password
4-octets PasswordLength
}
NewPasswordEncryptedWithOldNtPasswordHash(
IN 0-to-256-unicode-char NewPassword,
IN 0-to-256-unicode-char OldPassword,
OUT datatype-PWBLOCK EncryptedPwBlock )
{
NtPasswordHash( OldPassword, giving PasswordHash )
EncryptPwBlockWithPasswordHash( NewPassword,
PasswordHash,
giving EncryptedPwBlock )
}
Zorn Informational [Page 12]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
8.10. EncryptPwBlockWithPasswordHash()
EncryptPwBlockWithPasswordHash(
IN 0-to-256-unicode-char Password,
IN 16-octet PasswordHash,
OUT datatype-PWBLOCK PwBlock )
{
Fill ClearPwBlock with random octet values
PwSize = lstrlenW( Password ) * sizeof( unicode-char )
PwOffset = sizeof( ClearPwBlock.Password ) - PwSize
Move PwSize octets to (ClearPwBlock.Password + PwOffset ) from
Password
ClearPwBlock.PasswordLength = PwSize
Rc4Encrypt( ClearPwBlock,
sizeof( ClearPwBlock ),
PasswordHash,
sizeof( PasswordHash ),
giving PwBlock )
}
8.11. Rc4Encrypt()
Rc4Encrypt(
IN x-octet Clear,
IN integer ClearLength,
IN y-octet Key,
IN integer KeyLength,
OUT x-octet Cypher )
{
/*
* Use the RC4 encryption algorithm [6] to encrypt Clear of
* length ClearLength octets into a Cypher of the same length
* such that the Cypher can only be decrypted back to Clear
* by providing a Key of length KeyLength octets.
*/
}
Zorn Informational [Page 13]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
8.12. OldNtPasswordHashEncryptedWithNewNtPasswordHash()
OldNtPasswordHashEncryptedWithNewNtPasswordHash(
IN 0-to-256-unicode-char NewPassword,
IN 0-to-256-unicode-char OldPassword,
OUT 16-octet EncryptedPasswordHash )
{
NtPasswordHash( OldPassword, giving OldPasswordHash )
NtPasswordHash( NewPassword, giving NewPasswordHash )
NtPasswordHashEncryptedWithBlock( OldPasswordHash,
NewPasswordHash,
giving EncryptedPasswordHash )
}
8.13. NtPasswordHashEncryptedWithBlock()
NtPasswordHashEncryptedWithBlock(
IN 16-octet PasswordHash,
IN 16-octet Block,
OUT 16-octet Cypher )
{
DesEncrypt( 1st 8-octets PasswordHash,
1st 7-octets Block,
giving 1st 8-octets Cypher )
DesEncrypt( 2nd 8-octets PasswordHash,
2nd 7-octets Block,
giving 2nd 8-octets Cypher )
}
9. Examples
The following sections include protocol negotiation and hash
generation examples.
9.1. Negotiation Examples
Here are some examples of typical negotiations. The peer is on the
left and the authenticator is on the right.
The packet sequence ID is incremented on each authentication retry
response and on the change password response. All cases where the
packet sequence ID is updated are noted below.
Response retry is never allowed after Change Password. Change
Password may occur after response retry.
Zorn Informational [Page 14]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
9.1.1. Successful authentication
<- Authenticator Challenge
Peer Response/Challenge ->
<- Success/Authenticator Response
(Authenticator Response verification succeeds, call continues)
9.1.2. Authenticator authentication failure
<- Authenticator Challenge
Peer Response/Challenge ->
<- Success/Authenticator Response
(Authenticator Response verification fails, peer disconnects)
9.1.3. Failed authentication with no retry allowed
<- Authenticator Challenge
Peer Response/Challenge ->
<- Failure (E=691 R=0)
(Authenticator disconnects)
9.1.4. Successful authentication after retry
<- Authenticator Challenge
Peer Response/Challenge ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to challenge in failure message ->
<- Success/Authenticator Response
(Authenticator Response verification succeeds, call continues)
9.1.5. Failed hack attack with 3 attempts allowed
<- Authenticator Challenge
Peer Response/Challenge ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to challenge in Failure message ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to challenge in Failure message ->
<- Failure (E=691 R=0)
Zorn Informational [Page 15]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
9.1.6. Successful authentication with password change
<- Authenticator Challenge
Peer Response/Challenge ->
<- Failure (E=648 R=0 V=3), disable short
timeout
ChangePassword (++ID) to challenge in Failure message ->
<- Success/Authenticator Response
(Authenticator Response verification succeeds, call continues)
9.1.7. Successful authentication with retry and password change
<- Authenticator Challenge
Peer Response/Challenge ->
<- Failure (E=691 R=1), disable short timeout
Response (++ID) to first challenge+23 ->
<- Failure (E=648 R=0 V=2), disable short
timeout
ChangePassword (++ID) to first challenge+23 ->
<- Success/Authenticator Response
(Authenticator Response verification succeeds, call continues)
9.2. Hash Example
Intermediate values for user name "User" and password "clientPass".
All numeric values are hexadecimal.
0-to-256-char UserName:
55 73 65 72
0-to-256-unicode-char Password:
63 00 6C 00 69 00 65 00 6E 00 74 00 50 00 61 00 73 00 73 00
16-octet AuthenticatorChallenge:
5B 5D 7C 7D 7B 3F 2F 3E 3C 2C 60 21 32 26 26 28
16-octet PeerChallenge:
21 40 23 24 25 5E 26 2A 28 29 5F 2B 3A 33 7C 7E
8-octet Challenge:
D0 2E 43 86 BC E9 12 26
16-octet PasswordHash:
44 EB BA 8D 53 12 B8 D6 11 47 44 11 F5 69 89 AE
Zorn Informational [Page 16]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
24 octet NT-Response:
82 30 9E CD 8D 70 8B 5E A0 8F AA 39 81 CD 83 54 42 33 11 4A 3D 85 D6 DF
16-octet PasswordHashHash:
41 C0 0C 58 4B D2 D9 1C 40 17 A2 A1 2F A5 9F 3F
42-octet AuthenticatorResponse:
"S=407A5589115FD0D6209F510FE9C04566932CDA56"
9.3. Example of DES Key Generation
DES uses 56-bit keys, expanded to 64 bits by the insertion of parity
bits. After the parity of the key has been fixed, every eighth bit
is a parity bit and the number of bits that are set (1) in each octet
is odd; i.e., odd parity. Note that many DES engines do not check
parity, however, simply stripping the parity bits. The following
example illustrates the values resulting from the use of the password
"MyPw" to generate a pair of DES keys (e.g., for use in the
NtPasswordHashEncryptedWithBlock() described in section 8.13).
0-to-256-unicode-char Password:
4D 79 50 77
16-octet PasswordHash:
FC 15 6A F7 ED CD 6C 0E DD E3 33 7D 42 7F 4E AC
First "raw" DES key (initial 7 octets of password hash):
FC 15 6A F7 ED CD 6C
First parity-corrected DES key (eight octets):
FD 0B 5B 5E 7F 6E 34 D9
Second "raw" DES key (second 7 octets of password hash)
0E DD E3 33 7D 42 7F
Second parity-corrected DES key (eight octets):
0E 6E 79 67 37 EA 08 FE
10. Security Considerations
As an implementation detail, the authenticator SHOULD limit the
number of password retries allowed to make brute-force password
guessing attacks more difficult.
Zorn Informational [Page 17]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
11. References
[1] Simpson, W., "The Point-to-Point Protocol (PPP)", STD 51, RFC
1661, July 1994.
[2] Simpson, W., "PPP Challenge Handshake Authentication Protocol
(CHAP)", RFC 1994, August 1996.
[3] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[4] "Data Encryption Standard (DES)", Federal Information Processing
Standard Publication 46-2, National Institute of Standards and
Technology, December 1993.
[5] Rivest, R., "MD4 Message Digest Algorithm", RFC 1320, April
1992.
[6] RC4 is a proprietary encryption algorithm available under
license from RSA Data Security Inc. For licensing information,
contact:
RSA Data Security, Inc.
100 Marine Parkway
Redwood City, CA 94065-1031
[7] Eastlake, D., Crocker, S. and J. Schiller, "Randomness
Recommendations for Security", RFC 1750, December 1994.
[8] "The Unicode Standard, Version 2.0", The Unicode Consortium,
Addison-Wesley, 1996. ISBN 0-201-48345-9.
[9] Zorn, G. and Cobb, S., "Microsoft PPP CHAP Extensions", RFC
2433, October 1998.
[10] "DES Modes of Operation", Federal Information Processing
Standards Publication 81, National Institute of Standards and
Technology, December 1980.
[11] "Secure Hash Standard", Federal Information Processing Standards
Publication 180-1, National Institute of Standards and
Technology, April 1995.
[12] Zorn, G., "PPP LCP Internationalization Configuration Option",
RFC 2484, January 1999.
Zorn Informational [Page 18]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
12. Acknowledgements
Thanks (in no particular order) to Bruce Johnson, Tony Bell, Paul
Leach, Terence Spies, Dan Simon, Narendra Gidwani, Gurdeep Singh
Pall, Jody Terrill, Brad Robel-Forrest, and Joe Davies for useful
suggestions and feedback.
13. Author's Address
Questions about this memo can also be directed to:
Glen Zorn
Microsoft Corporation
One Microsoft Way
Redmond, Washington 98052
Phone: +1 425 703 1559
Fax: +1 425 936 7329
EMail: [email protected]
Zorn Informational [Page 19]
RFC 2759 Microsoft MS-CHAP-V2 January 2000
14. Full Copyright Statement
Copyright (C) The Internet Society (2000). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Zorn Informational [Page 20]
Html markup produced by rfcmarkup 1.124, available from https://tools.ietf.org/tools/rfcmarkup/