RK3576 Android平台开机log分析

下面的RK3576 EVB板子的开机log的分析

DDR 27ded95582 wesley.yao 24/05/28-17:43:19,fwver: v1.04
//DDR初始化，fwver: v1.04表示DDR bin的版本是1.04
In
ch0 ttot10
ch1 ttot10
ch0 ttot18
LPDDR4X, 2112MHz
//DDR初始化，fwver: v1.04表示DDR bin的版本是1.04

channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
ch1 ttot18
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
//DDR 双通道，总容量2048+2048=4096MB
Manufacturer ID:0x1
CH0 RX Vref:25.3%, RX DQS Vref:30.0%, TX Vref:21.8%,20.8%
DQ roc:
p0 n0, p1 n0, p0 n0, p1 n0, p1 n3, p5 n0, p2 n0, p6 n0, p0 n1,
p6 n2, p0 n1, p2 n5, p6 n0, p2 n0, p3 n4, p2 n0, p0 n0, p7 n2,
DQ rds:
h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
DQS roc: p0 n0, p0, n0
CH1 RX Vref:25.7%, RX DQS Vref:28.3%, TX Vref:20.8%,20.8%
DQ roc:
p1 n0, p1 n2, p0 n0, p0 n0, p2 n0, p0 n0, p1 n0, p5 n0, p0 n0,
p2 n0, p7 n0, p1 n1, p0 n0, p1 n0, p5 n0, p5 n1, p5 n0, p4 n0,
DQ rds:
h0 l0, h0 l1, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
h0 l0, h0 l0, h1 l0, h0 l0, h0 l0, h1 l0, h0 l0, h0 l0,
DQS roc: p0 n0, p2, n0
stride=0x3, ddr_config=0x4
hash bank_mask0-3 0x0 0x880 0x1100 0x2200, rank_mask0 0x400400
change to F1: 528MHz
ch0 ttot10
ch1 ttot10
change to F2: 1068MHz
ch0 ttot14
ch1 ttot14
change to F3: 1560MHz
ch0 ttot16
ch1 ttot16
change to F0: 2112MHz
ch0 ttot18
ch1 ttot18
out
//DDR初始化结束，DDR变频支持4个频点分别是：528MHz、1068MHz、1560MHz、2112MHz
U-Boot SPL board init
U-Boot SPL 2017.09-g3e169ed6d1d-220429 #lxh (May 21 2024 - 16:30:04), fwver: v1.04
//第一阶段是SPL，SPL版本是v1.04
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Device at ufs@2a2d0000 up at:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
Trying to boot from MMC2
// SPL 尝试初始化SD卡，如果有插SD卡优先从SD卡启动，这里没有识别到SD卡
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from UFS
//SPL 的flash初始化，本机是UFS的flash，下面是UFS的初始化信息
scanning bus for devices…
Device 0: (0:0) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 244040.0 MB = 238.3 GB (499793920 x 512)
UFS容量256GB
Device 0: (0:1) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 4.0 MB = 0.0 GB (8192 x 512)
Device 0: (0:2) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 4.0 MB = 0.0 GB (8192 x 512)
Device 0: (0:3) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 8.0 MB = 0.0 GB (16384 x 512)
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
//这个slot信息可以判断是否为A/B系统，这里只有_a表示非A/B，如果有显示_a _b则表示A/B系统，tries-remain: 表示系统异常启动还剩次数，当tries-remain: 0时系统会进入fastboot模式
Trying fit image at 0x4000 sector
Verified-boot: 0
Checking atf-1 0x40040000 … sha256(e486fb2255…) + OK
Checking uboot 0x40200000 … sha256(f2a2185c40…) + OK
Checking fdt 0x403430a8 … sha256(673916e062…) + OK
Checking atf-2 0x400f0000 … sha256(99ef39a641…) + OK
Checking atf-3 0x3fe70000 … sha256(2dbf17d3ab…) + OK
Checking optee 0x48400000 … sha256(988a2a2a76…) + OK
Jumping to U-Boot(0x40200000) via ARM Trusted Firmware(0x40040000)
Total: 109.826/638.411 ms

INFO: Preloader serial: 0
NOTICE: BL31: v2.3():v2.3-790-gd6d387faa:derrick.huang, fwver: v1.07
NOTICE: BL31: Built : 16:21:11, May 29 2024
//BL31即trust开始初始化，bl31版本是v1.07
INFO: ext 32k is detected
INFO: soc warm boot, reset status: 0x1
INFO: ARM GICv2 driver initialized
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 1
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-795-gb90c1680e #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon May 13 14:42:41 CST 2024 aarch64, fwver:
// bl32开始初始化，bl32是TEE
I/TC: OP-TEE memory: TEEOS 0x200000 TA 0xc00000 SHM 0x200000
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x40200000
INFO: SPSR = 0x3c9

U-Boot 2017.09-g0e1481a6ad8-240303-dirty #wlq (Jun 03 2024 - 16:46:50 +0800)
//UBOOT阶段初始化
Model: Rockchip RK3576 Evaluation board
MPIDR: 0x0
PreSerial: 0, raw, 0x2ad40000
DRAM: 4 GiB
Sysmem: init
Relocation Offset: bda1a000
Relocation fdt: fb9f9d90 - fb9fece8
CR: M/C/I
Using default environment

optee api revision: 2.0
scanning bus for devices…
Device at ufs@2a2d0000 up at:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
Device 0: (0:0) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 244040.0 MB = 238.3 GB (499793920 x 512)
Device 0: (0:1) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 4.0 MB = 0.0 GB (8192 x 512)
Device 0: (0:2) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 4.0 MB = 0.0 GB (8192 x 512)
Device 0: (0:3) Vendor: SAMSUNG Prod.: KLUEG4R1DE-B0F1 Rev: 0100
Type: Hard Disk
Capacity: 8.0 MB = 0.0 GB (16384 x 512)
Bootdev(atags): scsi 0
PartType: EFI
DM: v2
Android 14.0, Build 2024.2, v2
boot mode: normal
// boot mode信息可以看是否是烧写完固件第一次开机进recovery模式，如果是boot mode: recovery (misc)则表示是进recovery模式，这里的normal表示是进android 模式
RESC: ‘boot’, blk@0x0001ed54
Device is: UNLOCKED
DTB: rk-kernel.dtb
HASH(ce): OK
ANDROID: fdt overlay OK
dw_dp_bind zyb enter
I2c1 speed: 100000Hz
PMIC: RK8060 (on=0x40, off=0x00)
vdd_cpu_big_s0 init 850000 uV
vdd_npu_s0 750000 uV
vdd_cpu_lit_s0 init 850000 uV
vdd_gpu_s0 init 750000 uV
vdd_logic_s0 init 750000 uV
vdd_ddr_s0 850000 uV
//上面的log是电源PMIC模式初始化，PMID是RK806 通信接口是I2C，cpu、npu、gpu、logic、ddr等几路主要电源的电压值，如果开机这里没有打印这些信息就要硬件查一下pmic是否正常工作
Model: Rockchip RK3576 EVB1 V10 Board
Rockchip UBOOT DRM driver version: v1.0.1
Assign plane mask automatically
VOP have 3 active VP
vp0 have layer nr:1[2 ], primary plane: 2
vp1 have layer nr:1[3 ], primary plane: 3
vp2 have layer nr:1[8 ], primary plane: 8
disp info 2, type:16, id:0
base2_disp_info couldn’t be found, screen_info type[0] or id[0] mismatched
//上面显示的是vop的相关信息，包括各个vp的图层分配，显示屏DSI的分辨率信息等
Using display timing dts
dsi@27d80000: detailed mode clock 132000 kHz, flags[a]
H: 1080 1095 1099 1129
V: 1920 1935 1937 1952
//上面显示的是，显示屏DSI的分辨率信息1080 x 1920
bus_format: 100e
VOP update mode to: 1080x1920p60, type: MIPI0 for VP1
VP1 set crtc_clock to 132000KHz
Unsupported bt709f at 10bit csc depth, use bt601f instead
VOP VP1 enable Esmart1[654x270->654x270@213x825] fmt[0] addr[0xfdf00000]
final DSI-Link bandwidth: 880000 Kbps x 4
disp info 0, type:11, id:0
hdmi@27da0000 disconnected
CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
bpll 816000 KHz
lpll 816000 KHz
vpll 594000 KHz
aupll 786432 KHz
cpll 1000000 KHz
gpll 1188000 KHz
ppll 1300000 KHz
aclk_bus_root 396000 KHz
pclk_bus_root 100000 KHz
hclk_bus_root 198000 KHz
aclk_top 786432 KHz
aclk_top_mid 396000 KHz
pclk_top 100000 KHz
hclk_top 200000 KHz
//上面显示的是各个vp的图层分配信息
Net: Net Initialization Skipped
No ethernet found.
Hit key to stop autoboot(‘CTRL+C’): 0
ANDROID: reboot reason: “(none)”
// 上面的log表示启动原因，none是正常启动，recovery是要进recovery模式
Vboot=0, AVB images, AVB verify
read_is_device_unlocked() ops returned that device is UNLOCKED
//上面的log表示AVB没有上锁即不会进行AVB校验
avb_slot_verify.c:763: ERROR: vbmeta: Error verifying vbmeta image: OK_NOT_SIGNED
preloaded: distribute image from 'boot
ANDROID: sha1(b86c80c608…) + OK
Could not find “system” partition
Booting IMAGE kernel at 0x40400000 with fdt at 0x48300000…

Fdt Ramdisk skip relocation
Booting Android Image at 0x403ff800 …
Kernel: 0x40400000 - 0x42745008 (36117 KiB)
ramdisk: 0x4a200000 - 0x4a36403c (1425 KiB)
Flattened Device Tree blob at 0x48300000
Booting using the fdt blob at 0x48300000
XIP Kernel Image from 0x40400000 to 0x40400000 … OK
kernel loaded at 0x40400000, end = 0x42745008
Using Device Tree in place at 0000000048300000, end 0000000048344651
vp0, plane_mask:0x4, primary-id:2, curser-id:-1
vp1, plane_mask:0x8, primary-id:3, curser-id:-1
vp2, plane_mask:0x100, primary-id:8, curser-id:-1
reserved-memory:
vendor-storage-rm@00000000: addr=fbd58000 size=10000
drm-logo@0: addr=fdf00000 size=15a000
ramoops@40110000: addr=40110000 size=e0000
Adding bank: 0x40200000 - 0x48400000 (size: 0x08200000)
Adding bank: 0x49400000 - 0x100000000 (size: 0xb6c00000)
Adding bank: 0x100000000 - 0x140000000 (size: 0x40000000)
//上面的log表示DDR内存地址上报给kernel的地址信息
Total: 665.845/705.398 ms
//上面的log表示启动时间uboot阶段耗时/总的耗时

Starting kernel …
//开始进入kernel启动阶段

[ 0.718084][ T0] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.718110][ T0] Linux version 6.1.75 (wlq@sys2206) (Android (10087095, +pgo, +bolt, +lto, -mlgo, based on r487747c) clang version 17.0.2 (https://android.googlesource.com/toolchain/llvm-project d9f894
下面这行log显示kernel的编译信息和版本信息

[ 0.721402][ T0] random: crng init done
Machine model是定义在kernel的dts中，debug的时候可以修改这个字段用来判断dts是否更新成功

[ 0.726815][ T0] Machine model: Rockchip RK3576 EVB1 V10 Board
Machine model是定义在kernel的dts中，debug的时候可以修改这个字段用来判断dts是否更新成功[ 0.739996][ T0] earlycon: uart8250 at MMIO32 0x000000002ad40000 (options ‘’)
[ 0.744812][ T0] printk: bootconsole [uart8250] enabled
[ 0.745758][ T0] OF: fdt: Reserved memory: failed to reserve memory for node ‘drm-cubic-lut@0’: base 0x0000000000000000, size 0 MiB
[ 0.746948][ T0] OF: reserved mem: 0x0000000040110000…0x00000000401effff ( 896 KB ) map non-reusable ramoops@40110000
[ 0.747996][ T0] OF: reserved mem: 0x00000000fbd58000…0x00000000fbd67fff ( 64 KB ) map non-reusable vendor-storage-rm@00000000
[ 0.749114][ T0] OF: reserved mem: 0x00000000fdf00000…0x00000000fe059fff ( 1384 KB ) map non-reusable drm-logo@0
[ 0.827061][ T0] Zone ranges:
[ 0.827384][ T0] DMA32 [mem 0x0000000040200000-0x00000000ffffffff]
[ 0.828041][ T0] Normal [mem 0x0000000100000000-0x000000013fffffff]
[ 0.828694][ T0] Movable zone start for each node
[ 0.829164][ T0] Early memory node ranges
[ 0.829569][ T0] node 0: [mem 0x0000000040200000-0x00000000483fffff]
[ 0.830229][ T0] node 0: [mem 0x0000000049400000-0x000000013fffffff]
[ 0.830891][ T0] Initmem setup node 0 [mem 0x0000000040200000-0x000000013fffffff]
[ 0.832441][ T0] On node 0, zone DMA32: 512 pages in unavailable ranges
[ 0.850249][ T0] On node 0, zone DMA32: 4096 pages in unavailable ranges
[ 0.857102][ T0] cma: Reserved 16 MiB at 0x00000000ff000000
[ 0.858435][ T0] psci: probing for conduit method from DT.
[ 0.858986][ T0] psci: PSCIv1.1 detected in firmware.
[ 0.859490][ T0] psci: Using standard PSCI v0.2 function IDs
[ 0.860053][ T0] psci: Trusted OS migration not required
[ 0.860587][ T0] psci: SMC Calling Convention v1.2
[ 0.861414][ T0] percpu: Embedded 28 pages/cpu s75688 r8192 d30808 u114688
[ 0.862233][ T0] Detected VIPT I-cache on CPU0
[ 0.862718][ T0] CPU features: detected: ARM erratum 845719
[ 0.863273][ T0] alternatives: applying boot alternatives
[ 0.864427][ T0] Built 1 zonelists, mobility grouping on. Total pages: 1027592
[ 0.865155][ T0] Kernel command line: storagemedia=scsi androidboot.storagemedia=scsi androidboot.mode=normal androidboot.dtb_idx=0 androidboot.dtbo_idx=0 androidboot.verifiedbootstate=orange androi4
Kernel command line打印出所有的command 包括android上层定义、kernel dts中定义，uboot中动态添加的
[ 0.871279][ T0] Unknown kernel command line parameters “storagemedia=scsi”, will be passed to user space.
[ 0.872716][ T0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.873773][ T0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.874577][ T0] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[ 0.875286][ T0] software IO TLB: area num 8.
[ 0.891236][ T0] software IO TLB: mapped [mem 0x00000000f7d58000-0x00000000fbd58000] (64MB)
[ 0.941215][ T0] Memory: 3970404K/4175872K available (21376K kernel code, 4308K rwdata, 8464K rodata, 1856K init, 945K bss, 189084K reserved, 16384K cma-reserved)
Memory:打印内存使用及分布情况
[ 0.942738][ T0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.943513][ T0] trace event string verifier disabled
[ 0.944186][ T0] rcu: Preemptible hierarchical RCU implementation.
[ 0.944798][ T0] rcu: RCU event tracing is enabled.
[ 0.945293][ T0] rcu: RCU priority boosting: priority 1 delay 500 ms.
[ 0.945937][ T0] All grace periods are expedited (rcu_expedited).
[ 0.946546][ T0] Trampoline variant of Tasks RCU enabled.
[ 0.947089][ T0] Tracing variant of Tasks RCU enabled.
[ 0.947608][ T0] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.954322][ T0] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.958041][ T0] Root IRQ handler: gic_handle_irq
[ 0.958536][ T0] GIC: Using split EOI/Deactivate mode
[ 0.959691][ T0] rcu: Offload RCU callbacks from CPUs: 0-7.
[ 0.960274][ T0] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.984091][ T0] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.984741][ T0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.985800][ T0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.988359][ T0] kfence: initialized - using 524288 bytes for 63 objects at 0x(ptrval)-0x(ptrval)
[ 0.989472][ T0] Calibrating delay loop (skipped), value calculated using timer frequency… 48.00 BogoMIPS (lpj=96000)
[ 0.990485][ T0] pid_max: default: 32768 minimum: 301
[ 0.991024][ T0] LSM: Security Framework initializing
[ 0.991557][ T0] SELinux: Initializing.
[ 0.992029][ T0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.992782][ T0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.994587][ T1] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.995728][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.996458][ T1] cblist_init_generic: Setting shift to 3 and lim to 1.
[ 0.997161][ T1] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.997915][ T1] cblist_init_generic: Setting shift to 3 and lim to 1.
[ 0.998675][ T1] rcu: Hierarchical SRCU implementation.
[ 0.999180][ T1] rcu: Max phase no-delay instances is 1000.
[ 1.002551][ T1] smp: Bringing up secondary CPUs …
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[ 1.004221][ T0] Detected VIPT I-cache on CPU1
[ 1.004295][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 1
[ 1.004326][ T0] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 1.005513][ T0] Detected VIPT I-cache on CPU2
[ 1.005573][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 2
[ 1.005593][ T0] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 1.006787][ T0] Detected VIPT I-cache on CPU3
[ 1.006837][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 3
[ 1.006855][ T0] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 1.008087][ T0] CPU features: detected: Spectre-v3a
[ 1.008094][ T0] CPU features: detected: Spectre-BHB
[ 1.008097][ T0] CPU features: detected: ARM erratum 1742098
[ 1.008100][ T0] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 1.008102][ T0] Detected PIPT I-cache on CPU4
[ 1.008156][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 4
[ 1.008174][ T0] CPU4: Booted secondary processor 0x0000000100 [0x411fd080]
[ 1.009324][ T0] Detected PIPT I-cache on CPU5
[ 1.009367][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 5
[ 1.009379][ T0] CPU5: Booted secondary processor 0x0000000101 [0x411fd080]
[ 1.010539][ T0] Detected PIPT I-cache on CPU6
[ 1.010583][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 6
[ 1.010595][ T0] CPU6: Booted secondary processor 0x0000000102 [0x411fd080]
[ 1.011758][ T0] Detected PIPT I-cache on CPU7
[ 1.011803][ T0] cacheinfo: Unable to detect cache hierarchy for CPU 7
[ 1.011816][ T0] CPU7: Booted secondary processor 0x0000000103 [0x411fd080]
上面这段log是CPU的初始化，表示0-7个cpu核心都正常初始化，可以用来判断cpu硬件是否正常
[ 1.011878][ T1] smp: Brought up 1 node, 8 CPUs
[ 1.026507][ T1] SMP: Total of 8 processors activated.
[ 1.027009][ T1] CPU features: detected: 32-bit EL0 Support
[ 1.027545][ T1] CPU features: detected: CRC32 instructions
[ 1.028140][ T1] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 1.028997][ T1] CPU: All CPU(s) started at EL2
[ 1.029448][ T1] alternatives: applying system-wide alternatives
[ 1.034626][ T1] devtmpfs: initialized
[ 1.054461][ T1] Registered cp15_barrier emulation handler
[ 1.054994][ T1] Registered setend emulation handler
[ 1.055569][ T1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 1.056520][ T1] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 1.057413][ T1] pinctrl core: initialized pinctrl subsystem
[ 1.058519][ T1] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 1.059968][ T1] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 1.060770][ T1] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 1.061581][ T1] audit: initializing netlink subsys (disabled)
[ 1.062235][ T68] audit: type=2000 audit(0.072:1): state=initialized audit_enabled=0 res=1
[ 1.064134][ T1] Registered FIQ tty driver
[ 1.064689][ T1] thermal_sys: Registered thermal governor ‘fair_share’
[ 1.064693][ T1] thermal_sys: Registered thermal governor ‘step_wise’
[ 1.065308][ T1] thermal_sys: Registered thermal governor ‘user_space’
[ 1.065914][ T1] thermal_sys: Registered thermal governor ‘power_allocator’
[ 1.066570][ T1] cpuidle: using governor menu
[ 1.067816][ T1] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 1.068624][ T1] ASID allocator initialised with 65536 entries
[ 1.070486][ T1] ramoops: boot-log-0 0x8000@0x0000000040110000
[ 1.071071][ T1] ramoops: dmesg-0 0x14000@0x0000000040118000
[ 1.071607][ T1] ramoops: dmesg-1 0x14000@0x000000004012c000
[ 1.072756][ T1] ramoops: console 0x80000@0x0000000040140000
[ 1.073954][ T1] ramoops: pmsg 0x30000@0x00000000401c0000
[ 1.074822][ T1] printk: console [ramoops-1] enabled
[ 1.075461][ T1] pstore: Registered ramoops as persistent store backend
[ 1.076089][ T1] ramoops: using 0xe0000@0x40110000, ecc: 0
[ 1.079295][ T1] platform mipi0-csi2: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@1/endpoint@0
[ 1.080569][ T1] platform rkcif-mipi-lvds: Fixed dependency cycle(s) with /mipi0-csi2/ports/port@1/endpoint@0
[ 1.081668][ T1] platform rkisp-vir0: Fixed dependency cycle(s) with /rkcif-mipi-lvds-sditf/port/endpoint
[ 1.082782][ T1] platform rkvpss-vir0: Fixed dependency cycle(s) with /rkisp-vir0-sditf/port/endpoint
[ 1.094963][ T1] platform 27d80000.dsi: Fixed dependency cycle(s) with /dsi@27d80000/panel@0/ports/port@0/endpoint
[ 1.095962][ T1] platform 27d80000.dsi: Fixed dependency cycle(s) with /vop@27d00000/ports/port@1/endpoint@1
[ 1.097302][ T1] platform 27da0000.hdmi: Fixed dependency cycle(s) with /vop@27d00000/ports/port@0/endpoint@2
[ 1.098463][ T1] platform 27e40000.dp: Fixed dependency cycle(s) with /vop@27d00000/ports/port@2/endpoint@4
[ 1.122214][ T1] rockchip-gpio 27320000.gpio: probed /pinctrl/gpio@27320000
[ 1.123214][ T1] rockchip-gpio 2ae10000.gpio: probed /pinctrl/gpio@2ae10000
[ 1.124255][ T1] rockchip-gpio 2ae20000.gpio: probed /pinctrl/gpio@2ae20000
[ 1.125230][ T1] rockchip-gpio 2ae30000.gpio: probed /pinctrl/gpio@2ae30000
[ 1.126220][ T1] rockchip-gpio 2ae40000.gpio: probed /pinctrl/gpio@2ae40000
[ 1.126987][ T1] rockchip-pinctrl pinctrl: probed pinctrl
[ 1.132860][ T1] KASLR disabled due to lack of seed
[ 1.141890][ T1] fiq_debugger fiq_debugger.0: error -ENXIO: IRQ fiq not found
[ 1.142571][ T1] fiq_debugger fiq_debugger.0: error -ENXIO: IRQ wakeup not found
[ 1.143267][ T1] fiq_debugger_probe: could not install nmi irq handler
[[ 1.143928][ T1] printk: console [ttyFIQ0] enabled
1.143928][ T1] printk: console [ttyFIQ0] enabled
[ 1.144828][ T1] printk: bootconsole [uart8250] disabled
[ 1.144828][ T1] printk: bootconsole [uart8250] disabled
[ 1.145431][ T1] Registered fiq debugger ttyFIQ0
[ 1.148531][ T1] iommu: Default domain type: Translated
[ 1.148546][ T1] iommu: DMA domain TLB invalidation policy: strict mode
[ 1.148736][ T1] SCSI subsystem initialized
[ 1.148848][ T1] usbcore: registered new interface driver usbfs
[ 1.148873][ T1] usbcore: registered new interface driver hub
[ 1.148899][ T1] usbcore: registered new device driver usb
[ 1.149140][ T1] mc: Linux media interface: v0.10
[ 1.149168][ T1] videodev: Linux video capture interface: v2.00
[ 1.149204][ T1] pps_core: LinuxPPS API ver. 1 registered
[ 1.149212][ T1] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [email protected]
[ 1.149224][ T1] PTP clock support registered
[ 1.149254][ T1] EDAC MC: Ver: 3.0.0
[ 1.149783][ T1] arm-scmi firmware:scmi: Enabled polling mode TX channel - prot_id:16
[ 1.149868][ T1] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 1.149909][ T1] arm-scmi firmware:scmi: SCMI Protocol v2.0 ‘rockchip:’ Firmware version 0x0
[ 1.151343][ T1] Advanced Linux Sound Architecture Driver Initialized.
[ 1.151602][ T1] Bluetooth: Core ver 2.22
[ 1.151626][ T1] NET: Registered PF_BLUETOOTH protocol family
[ 1.151633][ T1] Bluetooth: HCI device and connection manager initialized
[ 1.151643][ T1] Bluetooth: HCI socket layer initialized
[ 1.151651][ T1] Bluetooth: L2CAP socket layer initialized
[ 1.151664][ T1] Bluetooth: SCO socket layer initialized
[ 1.153007][ T1] rockchip-cpuinfo cpuinfo: SoC : 35760000
[ 1.153021][ T1] rockchip-cpuinfo cpuinfo: Serial : 0000000000000000
[ 1.153542][ T1] clocksource: Switched to clocksource arch_sys_counter
[ 1.153743][ T1] VFS: Disk quotas dquot_6.6.0
[ 1.153774][ T1] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.154980][ T1] NET: Registered PF_INET protocol family
[ 1.155105][ T1] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.157003][ T1] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 1.157066][ T1] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.157080][ T1] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.157234][ T1] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[ 1.157796][ T1] TCP: Hash tables configured (established 32768 bind 32768)
[ 1.157881][ T1] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 1.157949][ T1] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 1.158088][ T1] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 1.158551][ T1] PCI: CLS 0 bytes, default 64
[ 1.159400][ T80] Trying to unpack rootfs image as initramfs…
[ 1.159440][ T1] rockchip-thermal 2ae70000.tsadc: Missing rockchip,grf property
[ 1.159639][ T1] thermal thermal_zone0: power_allocator: sustainable_power will be estimated
[ 1.159734][ T1] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 1.159916][ T1] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[ 1.160007][ T1] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[ 1.160100][ T1] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[ 1.160421][ T1] rockchip-thermal 2ae70000.tsadc: tsadc is probed successfully!
[ 1.161341][ T1] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 1.161692][ T1] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 1.163184][ T1] Initialise system trusted keyrings
[ 1.163345][ T1] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 1.166915][ T1] Key type cifs.idmap registered
[ 1.166934][ T1] fuse: init (API version 7.37)
[ 1.194732][ T1] Key type asymmetric registered
[ 1.194753][ T1] Asymmetric key parser ‘x509’ registered
[ 1.194798][ T1] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 1.194808][ T1] io scheduler mq-deadline registered
[ 1.194816][ T1] io scheduler kyber registered
[ 1.194912][ T1] io scheduler bfq registered
[ 1.195964][ T1] rockchip-csi2-dphy-hw 2b030000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[ 1.196107][ T1] rockchip-csi2-dphy-hw 2b070000.csi2-dphy1-hw: csi2 dphy hw probe successfully!
[ 1.197336][ T1] rockchip-usb2phy 2602e000.syscon:usb2-phy@0: error -ENXIO: IRQ index 0 not found
[ 1.198906][ T1] rockchip-usb2phy 2602e000.syscon:usb2-phy@2000: error -ENXIO: IRQ index 0 not found
[ 1.202791][ T80] Freeing initrd memory: 1424K
[ 1.203999][ T1] rockchip-hdptx-phy-hdmi 2b000000.hdmiphy: hdptx phy init success
[ 1.206598][ T99] rk-pcie 2a200000.pcie: invalid prsnt-gpios property in node
[ 1.206651][ T99] rk-pcie 2a200000.pcie: no vpcie3v3 regulator found
[ 1.206843][ T1] pwm-backlight backlight: supply power not found, using dummy regulator
[ 1.207088][ T99] rk-pcie 2a200000.pcie: max MSI vector is 8
[ 1.207135][ T99] rk-pcie 2a200000.pcie: host bridge /pcie@2a200000 ranges:
[ 1.207175][ T99] rk-pcie 2a200000.pcie: err 0x0020000000…0x00200fffff -> 0x0020000000
[ 1.207195][ T99] rk-pcie 2a200000.pcie: IO 0x0020100000…0x00201fffff -> 0x0020100000
[ 1.207200][ T1] iep: Module initialized.
[ 1.207227][ T99] rk-pcie 2a200000.pcie: MEM 0x0020200000…0x0020ffffff -> 0x0020200000
[ 1.207240][ T1] mpp_service mpp-srv: d9f56ab7afc1 author: Tingjin Huang 2024-05-31 video: rockchip: mpp: rkvenc2: Update address trans table
[ 1.207244][ T99] rk-pcie 2a200000.pcie: MEM 0x0900000000…0x097fffffff -> 0x0900000000
[ 1.207252][ T1] mpp_service mpp-srv: probe start
[ 1.207391][ T99] rk-pcie 2a200000.pcie: iATU unroll: enabled
[ 1.207405][ T99] rk-pcie 2a200000.pcie: iATU regions: 8 ob, 8 ib, align 64K, limit 8G
上面这段是PCIE的初始化，如果你们硬件没有PCIE，但是又有这段打印，且出现机器卡住无法开机，那么可能就是pcie没上电而软件又去初始pcie phy导致系统异常卡死，这时候可以在dts里面把pcie节点disabled掉
[ 1.209606][ T1] mpp_rkvenc2 rkvenc-ccu: probing start
[ 1.209621][ T1] mpp_rkvenc2 rkvenc-ccu: probing finish
[ 1.210253][ T1] mpp_service mpp-srv: probe success
[ 1.220513][ T1] dma-pl330 2ab90000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.220532][ T1] dma-pl330 2ab90000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.221443][ T1] dma-pl330 2abb0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.221453][ T1] dma-pl330 2abb0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.222363][ T1] dma-pl330 2abd0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.222374][ T1] dma-pl330 2abd0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.222931][ T1] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 1.223338][ T1] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
[ 1.223553][ T1] Serial: 8250/16550 driver, 15 ports, IRQ sharing disabled
[ 1.224279][ T1] 2ad70000.serial: ttyS4 at MMIO 0x2ad70000 (irq = 45, base_baud = 11718) is a 16550A
[ 1.230961][ T1] mipi-dsi 27d80000.dsi.0: Fixed dependency cycle(s) with /dsi@27d80000/ports/port@1/endpoint
[ 1.238476][ T22] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 1.242261][ T1] brd: module loaded
[ 1.247854][ T1] loop: module loaded
[ 1.248075][ T1] zram: Added device: zram0
[ 1.248625][ T1] system_heap: orders[0] = 6
[ 1.248633][ T1] system_heap: orders[1] = 4
[ 1.248638][ T1] system_heap: orders[2] = 0
[ 1.249094][ T1] SCSI Media Changer driver v0.25
[ 1.251002][ T1] tun: Universal TUN/TAP device driver, 1.6
[ 1.251776][ T1] rk_gmac-dwmac 2a220000.ethernet: IRQ eth_lpi not found
[ 1.251933][ T1] rk_gmac-dwmac 2a220000.ethernet: supply phy not found, using dummy regulator
[ 1.252002][ T1] rk_gmac-dwmac 2a220000.ethernet: clock input or output? (output).
[ 1.252012][ T1] rk_gmac-dwmac 2a220000.ethernet: TX delay(0x21).
[ 1.252019][ T1] rk_gmac-dwmac 2a220000.ethernet: Can not read property: rx_delay.
[ 1.252026][ T1] rk_gmac-dwmac 2a220000.ethernet: set rx_delay to 0xffffffff
[ 1.252091][ T1] rk_gmac-dwmac 2a220000.ethernet: integrated PHY? (no).
[ 1.252101][ T1] rk_gmac-dwmac 2a220000.ethernet: cannot get clock mac_clk_rx
[ 1.252109][ T1] rk_gmac-dwmac 2a220000.ethernet: cannot get clock mac_clk_tx
[ 1.252124][ T1] rk_gmac-dwmac 2a220000.ethernet: cannot get clock clk_mac_speed
[ 1.252350][ T1] rk_gmac-dwmac 2a220000.ethernet: init for RGMII_RXID
[ 1.252444][ T1] rk_gmac-dwmac 2a220000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 1.252454][ T1] rk_gmac-dwmac 2a220000.ethernet: DWMAC4/5
[ 1.252463][ T1] rk_gmac-dwmac 2a220000.ethernet: DMA HW capability register supported
[ 1.252470][ T1] rk_gmac-dwmac 2a220000.ethernet: RX Checksum Offload Engine supported
[ 1.252475][ T1] rk_gmac-dwmac 2a220000.ethernet: TX Checksum insertion supported
[ 1.252481][ T1] rk_gmac-dwmac 2a220000.ethernet: Wake-Up On Lan supported
[ 1.252516][ T1] rk_gmac-dwmac 2a220000.ethernet: TSO supported
[ 1.252523][ T1] rk_gmac-dwmac 2a220000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.252531][ T1] rk_gmac-dwmac 2a220000.ethernet: Enabled L3L4 Flow TC (entries=2)
[ 1.252538][ T1] rk_gmac-dwmac 2a220000.ethernet: Enabled RFS Flow TC (entries=10)
[ 1.252545][ T1] rk_gmac-dwmac 2a220000.ethernet: TSO feature enabled
[ 1.252552][ T1] rk_gmac-dwmac 2a220000.ethernet: Using 40/40 bits DMA host/device width
[ 1.386704][ T1] rk_gmac-dwmac 2a230000.ethernet: IRQ eth_lpi not found
[ 1.386865][ T1] rk_gmac-dwmac 2a230000.ethernet: supply phy not found, using dummy regulator
[ 1.386932][ T1] rk_gmac-dwmac 2a230000.ethernet: clock input or output? (output).
[ 1.386941][ T1] rk_gmac-dwmac 2a230000.ethernet: TX delay(0x20).
[ 1.386949][ T1] rk_gmac-dwmac 2a230000.ethernet: Can not read property: rx_delay.
[ 1.386955][ T1] rk_gmac-dwmac 2a230000.ethernet: set rx_delay to 0xffffffff
[ 1.386971][ T1] rk_gmac-dwmac 2a230000.ethernet: integrated PHY? (no).
[ 1.386979][ T1] rk_gmac-dwmac 2a230000.ethernet: cannot get clock mac_clk_rx
[ 1.386987][ T1] rk_gmac-dwmac 2a230000.ethernet: cannot get clock mac_clk_tx
[ 1.387003][ T1] rk_gmac-dwmac 2a230000.ethernet: cannot get clock clk_mac_speed
[ 1.387227][ T1] rk_gmac-dwmac 2a230000.ethernet: init for RGMII_RXID
[ 1.387327][ T1] rk_gmac-dwmac 2a230000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 1.387336][ T1] rk_gmac-dwmac 2a230000.ethernet: DWMAC4/5
[ 1.387345][ T1] rk_gmac-dwmac 2a230000.ethernet: DMA HW capability register supported
[ 1.387351][ T1] rk_gmac-dwmac 2a230000.ethernet: RX Checksum Offload Engine supported
[ 1.387357][ T1] rk_gmac-dwmac 2a230000.ethernet: TX Checksum insertion supported
[ 1.387364][ T1] rk_gmac-dwmac 2a230000.ethernet: Wake-Up On Lan supported
[ 1.387398][ T1] rk_gmac-dwmac 2a230000.ethernet: TSO supported
[ 1.387405][ T1] rk_gmac-dwmac 2a230000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.387412][ T1] rk_gmac-dwmac 2a230000.ethernet: Enabled L3L4 Flow TC (entries=2)
[ 1.387419][ T1] rk_gmac-dwmac 2a230000.ethernet: Enabled RFS Flow TC (entries=10)
[ 1.387426][ T1] rk_gmac-dwmac 2a230000.ethernet: TSO feature enabled
[ 1.387433][ T1] rk_gmac-dwmac 2a230000.ethernet: Using 40/40 bits DMA host/device width
[ 1.414668][ T99] rk-pcie 2a200000.pcie: PCIe Linking… LTSSM is 0x3
[ 1.501553][ T99] rk-pcie 2a200000.pcie: PCIe Link up, LTSSM is 0x30011
[ 1.501568][ T99] rk-pcie 2a200000.pcie: PCIe Gen.1 x1 link up
[ 1.501698][ T99] rk-pcie 2a200000.pcie: PCI host bridge to bus 0000:00
[ 1.501712][ T99] pci_bus 0000:00: root bus resource [bus 00-0f]
[ 1.501725][ T99] pci_bus 0000:00: root bus resource [??? 0x20000000-0x200fffff flags 0x0]
[ 1.501737][ T99] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x20100000-0x201fffff])
[ 1.501748][ T99] pci_bus 0000:00: root bus resource [mem 0x20200000-0x20ffffff]
[ 1.501759][ T99] pci_bus 0000:00: root bus resource [mem 0x900000000-0x97fffffff pref]
[ 1.501792][ T99] pci 0000:00:00.0: [1d87:3576] type 01 class 0x060400
[ 1.501862][ T99] pci 0000:00:00.0: supports D1 D2
[ 1.501872][ T99] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.520307][ T99] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-0f] (conflicts with (null) [bus 00-0f])
[ 1.520421][ T99] pci 0000:01:00.0: [14e4:449d] type 00 class 0x028000
[ 1.520511][ T99] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[ 1.520568][ T99] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit]
[ 1.521059][ T99] pci 0000:01:00.0: supports D1 D2
[ 1.521070][ T99] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.522412][ T1] PPP generic driver version 2.4.2
[ 1.522525][ T1] PPP BSD Compression module registered
[ 1.522532][ T1] PPP Deflate Compression module registered
[ 1.522547][ T1] PPP MPPE Compression module registered
[ 1.522554][ T1] NET: Registered PF_PPPOX protocol family
[ 1.522569][ T1] PPTP driver version 0.8.5
[ 1.522726][ T1] usbcore: registered new interface driver catc
[ 1.522749][ T1] usbcore: registered new interface driver kaweth
[ 1.522756][ T1] pegasus: Pegasus/Pegasus II USB Ethernet driver
[ 1.522773][ T1] usbcore: registered new interface driver pegasus
[ 1.522791][ T1] usbcore: registered new interface driver rtl8150
[ 1.522806][ T1] usbcore: registered new device driver r8152-cfgselector
[ 1.522827][ T1] usbcore: registered new interface driver r8152
[ 1.522833][ T1] hso: drivers/net/usb/hso.c: Option Wireless
[ 1.522860][ T1] usbcore: registered new interface driver hso
[ 1.522879][ T1] usbcore: registered new interface driver asix
[ 1.522899][ T1] usbcore: registered new interface driver ax88179_178a
[ 1.522917][ T1] usbcore: registered new interface driver cdc_ether
[ 1.522936][ T1] usbcore: registered new interface driver cdc_eem
[ 1.522955][ T1] usbcore: registered new interface driver dm9601
[ 1.522977][ T1] usbcore: registered new interface driver smsc75xx
[ 1.522997][ T1] usbcore: registered new interface driver smsc95xx
[ 1.523015][ T1] usbcore: registered new interface driver gl620a
[ 1.523035][ T1] usbcore: registered new interface driver net1080
[ 1.523054][ T1] usbcore: registered new interface driver plusb
[ 1.523072][ T1] usbcore: registered new interface driver rndis_host
[ 1.523091][ T1] usbcore: registered new interface driver cdc_subset
[ 1.523108][ T1] usbcore: registered new interface driver zaurus
[ 1.523127][ T1] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 1.523149][ T1] usbcore: registered new interface driver int51x1
[ 1.523167][ T1] usbcore: registered new interface driver kalmia
[ 1.523185][ T1] usbcore: registered new interface driver ipheth
[ 1.523204][ T1] usbcore: registered new interface driver sierra_net
[ 1.523223][ T1] usbcore: registered new interface driver cx82310_eth
[ 1.523245][ T1] usbcore: registered new interface driver cdc_ncm
[ 1.523263][ T1] usbcore: registered new interface driver qmi_wwan
[ 1.523282][ T1] usbcore: registered new interface driver cdc_mbim
[ 1.523300][ T1] usbcore: registered new interface driver r8153_ecm
[ 1.527969][ T1] phy phy-2602e000.syscon:[email protected]: illegal mode
[ 1.527984][ T1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.528066][ T1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 1.528134][ T1] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000808002010010
[ 1.528162][ T1] xhci-hcd xhci-hcd.0.auto: irq 64, io mem 0x23400000
[ 1.528248][ T1] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 1.528319][ T1] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 1.528329][ T1] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 1.528409][ T1] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[ 1.528419][ T1] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.528426][ T1] usb usb1: Product: xHCI Host Controller
[ 1.528432][ T1] usb usb1: Manufacturer: Linux 6.1.75 xhci-hcd
[ 1.528438][ T1] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 1.528699][ T1] hub 1-0:1.0: USB hub found
[ 1.528718][ T1] hub 1-0:1.0: 1 port detected
[ 1.528891][ T1] usb usb2: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 1.528947][ T1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[ 1.528956][ T1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.528963][ T1] usb usb2: Product: xHCI Host Controller
[ 1.528969][ T1] usb usb2: Manufacturer: Linux 6.1.75 xhci-hcd
[ 1.528975][ T1] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 1.529182][ T1] hub 2-0:1.0: USB hub found
[ 1.529200][ T1] hub 2-0:1.0: 1 port detected
[ 1.529388][ T1] usbcore: registered new interface driver cdc_acm
[ 1.529396][ T1] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.529421][ T1] usbcore: registered new interface driver usblp
[ 1.529443][ T1] usbcore: registered new interface driver cdc_wdm
[ 1.529610][ T1] usbcore: registered new interface driver uas
[ 1.529642][ T1] usbcore: registered new interface driver usb-storage
[ 1.529661][ T1] usbcore: registered new interface driver ums-alauda
[ 1.529682][ T1] usbcore: registered new interface driver ums-cypress
[ 1.529702][ T1] usbcore: registered new interface driver ums-datafab
[ 1.529721][ T1] usbcore: registered new interface driver ums_eneub6250
[ 1.529741][ T1] usbcore: registered new interface driver ums-freecom
[ 1.529761][ T1] usbcore: registered new interface driver ums-isd200
[ 1.529781][ T1] usbcore: registered new interface driver ums-jumpshot
[ 1.529800][ T1] usbcore: registered new interface driver ums-karma
[ 1.529819][ T1] usbcore: registered new interface driver ums-onetouch
[ 1.529839][ T1] usbcore: registered new interface driver ums-sddr09
[ 1.529858][ T1] usbcore: registered new interface driver ums-sddr55
[ 1.529877][ T1] usbcore: registered new interface driver ums-usbat
[ 1.529918][ T1] usbcore: registered new interface driver usbserial_generic
[ 1.529932][ T1] usbserial: USB Serial support registered for generic
[ 1.529952][ T1] usbcore: registered new interface driver option
[ 1.529964][ T1] usbserial: USB Serial support registered for GSM modem (1-port)
[ 1.530002][ T1] usbcore: registered new interface driver trancevibrator
[ 1.530437][ T1] usbcore: registered new interface driver xpad
[ 1.530464][ T1] usbcore: registered new interface driver usb_acecad
[ 1.530486][ T1] usbcore: registered new interface driver aiptek
[ 1.530509][ T1] usbcore: registered new interface driver hanwang
[ 1.530529][ T1] usbcore: registered new interface driver kbtab
[ 1.530536][ T1] CTS-SPIDrv Chipone touch driver init, version: v3.6.3
[ 1.530541][ T1] CTS-SPIDrv - Register i2c driver
[ 1.530566][ T1] CTS-SPIDrv - Register touch driver successfully
[ 1.530580][ T1] cyttsp5_loader_init: Parade TTSP FW Loader Driver (Built TTDA.03.08.874312) rc=0
[ 1.530646][ T1] pt_loader_init: Parade FW Loader Driver (Version TTDL.04.11.977092) rc=0
[ 1.530858][ T1] … rk pwm remotectl v2.0 init
[ 1.531002][ T1] input: 27330000.pwm as /devices/platform/27330000.pwm/input/input0
[ 1.531164][ T1] remotectl-pwm 27330000.pwm: pwm sip wakeup config error!!
[ 1.531172][ T1] remotectl-pwm 27330000.pwm: Donot support ATF Wakeup
[ 1.531967][ T1] i2c_dev: i2c /dev entries driver
[ 1.533347][ T1] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs1_pwrdn
[ 1.533367][ T1] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs3_null
[ 1.533380][ T1] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs2_null
[ 1.533393][ T1] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs1_null
[ 1.533631][ T99] pci 0000:00:00.0: BAR 8: assigned [mem 0x20200000-0x207fffff]
[ 1.533647][ T99] pci 0000:01:00.0: BAR 2: assigned [mem 0x20400000-0x207fffff 64bit]
[ 1.533693][ T99] pci 0000:01:00.0: BAR 0: assigned [mem 0x20200000-0x2020ffff 64bit]
[ 1.533737][ T99] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.533747][ T99] pci 0000:00:00.0: bridge window [mem 0x20200000-0x207fffff]
[ 1.534461][ T99] pcieport 0000:00:00.0: PME: Signaling with IRQ 70
[ 1.535039][ T1] rk806 1-0023: chip id: RK806,ver:0xa, 0x5
[ 1.535932][ T1] rk806 1-0023: ON: 0x40 OFF:0x0
[ 1.545511][ T1] input: rk805 pwrkey as /devices/platform/2ac40000.i2c/i2c-1/1-0023/rk805-pwrkey.2.auto/input/input1
[ 1.595183][ T1] rk806 1-0023: no sleep-setting state
[ 1.595201][ T1] rk806 1-0023: no reset-setting pinctrl state
[ 1.595208][ T1] rk806 1-0023: no dvs-setting pinctrl state
上面这段是PMIC RK806初始，如果这里显示的chip id: 不是RK806，而是乱码或者空，就要硬件检查一下PMIC RK806是否贴好
[ 1.606839][ T1] rtc-hym8563 2-0051: rtc information is valid
[ 1.613945][ T1] rtc-hym8563 2-0051: registered as rtc0
[ 1.614960][ T1] rtc-hym8563 2-0051: setting system clock to 2024-06-04T02:18:27 UTC (1717467507)
[ 1.615079][ T1] i2c 2-004e: Fixed dependency cycle(s) with /usb@23000000/port/endpoint
[ 1.618695][ T1] i2c 4-001a: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@1
[ 1.618845][ T1] i2c i2c-4: 1 i2c clients have been registered at 0x1a
[ 1.618922][ T1] i2c 4-001a-1: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@2
[ 1.619129][ T1] i2c 4-0030: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@4
[ 1.619334][ T1] i2c 4-0036: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@3
[ 1.619469][ T1] i2c i2c-4: 1 i2c clients have been registered at 0x36
[ 1.619540][ T1] i2c 4-0036-1: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@5
[ 1.620353][ T1] gsensor_icm4260x 7-0068: sensor_register_device: icm4260x_acc, id = 38
[ 1.620377][ T1] i2c i2c-7: sensor_probe: icm42607_acc,00000000911f704a
[ 1.620503][ T1] gsensor_icm4260x 7-0068: sensor_chip_init:icm42607_acc:devid=0x0,ops=0x0000000080e9766b
[ 1.720912][ T1] input: gsensor as /devices/platform/2aca0000.i2c/i2c-7/7-0068/input/input2
[ 1.721016][ T1] gsensor_icm4260x 7-0068: sensor_irq_init:use polling,delay=30 ms
[ 1.721097][ T1] gsensor_icm4260x 7-0068: sensor_misc_device_register:miscdevice: mma8452_daemon
[ 1.721109][ T1] gsensor_icm4260x 7-0068: sensor_probe:initialized ok,sensor name:icm4260x_acc,type:2,id=38
[ 1.721109][ T1]
[ 1.721150][ T1] i2c i2c-7: 1 i2c clients have been registered at 0x68
[ 1.722559][ T1] rkcifhw 27c10000.rkcif: Adding to iommu group 9
[ 1.723037][ T1] rkcifhw 27c10000.rkcif: No reserved memory region assign to CIF
[ 1.723175][ T1] rkcif rkcif-mipi-lvds: Adding to iommu group 9
[ 1.723198][ T1] rkcif rkcif-mipi-lvds: rkcif driver version: v00.02.00
[ 1.723308][ T1] rkcif rkcif-mipi-lvds: attach to cif hw node
[ 1.723319][ T1] rkcif rkcif-mipi-lvds: rkcif wait line 0
[ 1.723328][ T1] rkcif rkcif-mipi-lvds: rkcif fastboot reserve bufs num 3
[ 1.723342][ T1] : terminal subdev does not exist
[ 1.723353][ T1] : terminal subdev does not exist
[ 1.723362][ T1] : terminal subdev does not exist
[ 1.723371][ T1] : terminal subdev does not exist
[ 1.723380][ T1] : get_remote_sensor: video pad[0] is null
[ 1.723388][ T1] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 1.723398][ T1] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
[ 1.723409][ T1] : get_remote_sensor: video pad[0] is null
[ 1.723416][ T1] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 1.723425][ T1] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
[ 1.723435][ T1] : get_remote_sensor: video pad[0] is null
[ 1.723442][ T1] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 1.723451][ T1] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
[ 1.723461][ T1] : get_remote_sensor: video pad[0] is null
[ 1.723468][ T1] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 1.723477][ T1] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
[ 1.724538][ T1] rkcif rkcif-mipi-lvds: No memory-region-thunderboot specified
[ 1.725868][ T1] rockchip-mipi-csi2-hw 27c80000.mipi0-csi2-hw: enter mipi csi2 hw probe!
[ 1.726023][ T1] rockchip-mipi-csi2-hw 27c80000.mipi0-csi2-hw: probe success, v4l2_dev:mipi0-csi2-hw!
[ 1.726072][ T1] rockchip-mipi-csi2-hw 27c90000.mipi1-csi2-hw: enter mipi csi2 hw probe!
[ 1.726174][ T1] rockchip-mipi-csi2-hw 27c90000.mipi1-csi2-hw: probe success, v4l2_dev:mipi1-csi2-hw!
[ 1.726222][ T1] rockchip-mipi-csi2-hw 27ca0000.mipi2-csi2-hw: enter mipi csi2 hw probe!
[ 1.726336][ T1] rockchip-mipi-csi2-hw 27ca0000.mipi2-csi2-hw: probe success, v4l2_dev:mipi2-csi2-hw!
[ 1.726382][ T1] rockchip-mipi-csi2-hw 27cb0000.mipi3-csi2-hw: enter mipi csi2 hw probe!
[ 1.726482][ T1] rockchip-mipi-csi2-hw 27cb0000.mipi3-csi2-hw: probe success, v4l2_dev:mipi3-csi2-hw!
[ 1.726528][ T1] rockchip-mipi-csi2-hw 27cc0000.mipi4-csi2-hw: enter mipi csi2 hw probe!
[ 1.726627][ T1] rockchip-mipi-csi2-hw 27cc0000.mipi4-csi2-hw: probe success, v4l2_dev:mipi4-csi2-hw!
[ 1.727121][ T1] rockchip-mipi-csi2 mipi0-csi2: attach to csi2 hw node
[ 1.727158][ T1] rkcif rkcif-mipi-lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 1.727173][ T1] rockchip-mipi-csi2: Async registered subdev
[ 1.727182][ T1] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds!
[ 1.728375][ T1] rkisp_hw 27c00000.isp: Adding to iommu group 8
[ 1.728554][ T1] rkisp_hw 27c00000.isp: is_thunderboot: 0
[ 1.728568][ T1] rkisp_hw 27c00000.isp: Missing rockchip,grf property
[ 1.728598][ T1] rkisp_hw 27c00000.isp: max input:0x0@0fps
[ 1.728761][ T1] rkisp_hw 27c00000.isp: no find phandle sram
[ 1.729118][ T1] rkisp rkisp-vir0: rkisp driver version: v02.06.00
[ 1.729218][ T1] rkisp rkisp-vir0: No memory-region-thunderboot specified
[ 1.729348][ T1] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 1.731525][ T1] rkvpss_hw 27c30000.vpss: Adding to iommu group 10
[ 1.731816][ T1] rkvpss_hw 27c30000.vpss: failed to get cru reset
[ 1.732228][ T1] rkvpss rkvpss-vir0: rkvpss driver version: v00.01.00
[ 1.732816][ T1] rkvpss-vir0: Async subdev notifier completed
[ 1.733216][ T1] usbcore: registered new interface driver uvcvideo
[ 1.734311][ T1] __power_supply_register: Expected proper parent device for ‘test_ac’
[ 1.734544][ T1] __power_supply_register: Expected proper parent device for ‘test_battery’
[ 1.734771][ T1] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[ 1.734875][ T1] __power_supply_register: Expected proper parent device for ‘test_usb’
[ 1.736248][ T1] device-mapper: uevent: version 1.0.3
[ 1.736417][ T1] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: [email protected]
[ 1.736579][ T1] Bluetooth: HCI UART driver ver 2.3
[ 1.736591][ T1] Bluetooth: HCI UART protocol H4 registered
[ 1.738199][ T1] cpu cpu0: bin=0
[ 1.738438][ T1] cpu cpu0: leakage=0
[ 1.740661][ T1] cpu cpu0: pvtm=1958
[ 1.741213][ T1] cpu cpu0: pvtm-volt-sel=1
[ 1.742595][ T1] cpu cpu4: bin=0
[ 1.742822][ T1] cpu cpu4: leakage=0
[ 1.745033][ T1] cpu cpu4: pvtm=2082
[ 1.745614][ T1] cpu cpu4: pvtm-volt-sel=1
[ 1.747561][ T1] cpu cpu0: avs=0
[ 1.748807][ T1] cpu cpu4: avs=0
[ 1.748932][ T1] cpu cpu0: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 1.750220][ T1] cpu cpu0: EM: created perf domain
[ 1.751251][ T1] cpu cpu4: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 1.752588][ T1] cpu cpu4: EM: created perf domain
上面这段是CPU变频初始化，注意这段log需要在PMIC RK806初始化log的后面，如果在前面者会出现cpu变频初始化失败，因为cpu变频依赖电源模块，出现这种情况需要在dts里面调整电源相关配置的顺序
[ 1.754699][ T1] sdhci: Secure Digital Host Controller Interface driver
[ 1.754721][ T1] sdhci: Copyright© Pierre Ossman
[ 1.754730][ T1] Synopsys Designware Multimedia Card Interface Driver
[ 1.755362][ T1] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.756040][ T8] dwmmc_rockchip 2a310000.mmc: No normal pinctrl state
[ 1.756062][ T8] dwmmc_rockchip 2a310000.mmc: No idle pinctrl state
[ 1.756323][ T8] dwmmc_rockchip 2a310000.mmc: IDMAC supports 32-bit address mode.
[ 1.756376][ T8] dwmmc_rockchip 2a310000.mmc: Using internal DMA controller.
[ 1.756391][ T8] dwmmc_rockchip 2a310000.mmc: Version ID is 270a
[ 1.756435][ T8] dwmmc_rockchip 2a310000.mmc: DW MMC controller at irq 97,32 bit host data width,256 deep fifo
[ 1.757334][ T80] mmc1: CQHCI version 5.10
[ 1.757668][ T1] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
[ 1.757693][ T1] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled
[ 1.757707][ T1] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
[ 1.757719][ T1] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
[ 1.758622][ T1] scsi host0: ufshcd
[ 1.762208][ T1] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 1.762333][ T1] SMCCC: SOC_ID: ID = jep106:0001:0002 Revision = 0xfffffffd
[ 1.763194][ T1] cryptodev: driver 1.12 loaded.
[ 1.763246][ T1] hid: raw HID events driver © Jiri Kosina
[ 1.765621][ T1] usbcore: registered new interface driver usbhid
[ 1.765634][ T1] usbhid: USB HID core driver
[ 1.765935][ T1] ashmem: initialized
[ 1.768571][ T8] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 1.770569][ T1] optee: probing for conduit method.
[ 1.770593][ T1] optee: revision 3.13 (b90c1680)
[ 1.770902][ T1] optee: dynamic shared memory is enabled
[ 1.771013][ T1] optee: initialized driver
[ 1.771513][ T1] usbcore: registered new interface driver snd-usb-audio
[ 1.778739][ T1] input: headset-keys as /devices/platform/es8388-sound/input/input3
[ 1.783312][ T10] scsi 0:0:0:49488: Well-known LUN SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.784353][ T10] ufs_device_wlun 0:0:0:49488: Attached scsi generic sg0 type 30
[ 1.784640][ T10] scsi 0:0:0:49476: Well-known LUN SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.785523][ T10] scsi 0:0:0:49476: Attached scsi generic sg1 type 30
[ 1.785788][ T10] scsi 0:0:0:49456: Well-known LUN SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.786710][ T10] scsi 0:0:0:49456: Attached scsi generic sg2 type 30
[ 1.787390][ T10] scsi 0:0:0:0: Direct-Access SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.788224][ T10] scsi 0:0:0:1: Direct-Access SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.788515][ T80] mmc1: SDHCI controller on 2a330000.mmc [2a330000.mmc] using ADMA 64-bit
[ 1.789022][ T10] scsi 0:0:0:2: Direct-Access SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.789683][ T1] ES8323 3-0010: ASoC: error at soc_component_write_no_lock on ES8323.3-0010 for register: [0x00000035] -5
[ 1.789839][ T10] scsi 0:0:0:3: Direct-Access SAMSUNG KLUEG4R1DE-B0F1 0100 PQ: 0 ANSI: 6
[ 1.790811][ T10] sd 0:0:0:0: Attached scsi generic sg3 type 0
[ 1.790997][ T80] sd 0:0:0:0: [sda] 62474240 4096-byte logical blocks: (256 GB/238 GiB)
[ 1.791062][ T80] sd 0:0:0:0: [sda] Write Protect is off
[ 1.791179][ T80] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 1.791191][ T80] sd 0:0:0:0: [sda] Preferred minimum I/O size 524288 bytes
[ 1.791201][ T80] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes
[ 1.791271][ T10] sd 0:0:0:1: Attached scsi generic sg4 type 0
[ 1.791603][ T8] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
[ 1.791700][ T8] sd 0:0:0:1: [sdb] Write Protect is off
[ 1.791724][ T10] sd 0:0:0:2: Attached scsi generic sg5 type 0
[ 1.791809][ T8] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 1.791821][ T8] sd 0:0:0:1: [sdb] Preferred minimum I/O size 524288 bytes
[ 1.791829][ T8] sd 0:0:0:1: [sdb] Optimal transfer size 524288 bytes
[ 1.792022][ T142] sd 0:0:0:2: [sdc] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
[ 1.792079][ T142] sd 0:0:0:2: [sdc] Write Protect is off
[ 1.792174][ T142] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 1.792184][ T142] sd 0:0:0:2: [sdc] Preferred minimum I/O size 524288 bytes
[ 1.792193][ T142] sd 0:0:0:2: [sdc] Optimal transfer size 524288 bytes
[ 1.792342][ T10] sd 0:0:0:3: Attached scsi generic sg6 type 0
[ 1.793281][ T143] sd 0:0:0:3: [sdd] 2048 4096-byte logical blocks: (8.39 MB/8.00 MiB)
[ 1.793442][ T143] sd 0:0:0:3: [sdd] Write Protect is off
[ 1.793569][ T143] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 1.793583][ T143] sd 0:0:0:3: [sdd] Preferred minimum I/O size 524288 bytes
[ 1.793592][ T143] sd 0:0:0:3: [sdd] Optimal transfer size 524288 bytes
[ 1.793940][ T142] sd 0:0:0:2: [sdc] Attached SCSI disk
[ 1.793977][ T8] sd 0:0:0:1: [sdb] Attached SCSI disk
[ 1.795109][ T80] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15
[ 1.795344][ T143] sd 0:0:0:3: [sdd] Attached SCSI disk
[ 1.796686][ T80] sd 0:0:0:0: [sda] Attached SCSI disk
上面这段是FLASH SSD的初始化
[ 1.837600][ T1] input: rockchip-es8388 Headset as /devices/platform/es8388-sound/sound/card0/input4
[ 1.838086][ T1] Mirror/redirect action on
[ 1.838106][ T1] netem: version 1.3
[ 1.838113][ T1] u32 classifier
[ 1.838119][ T1] input device check on
[ 1.838124][ T1] Actions configured
[ 1.838663][ T1] xt_time: kernel timezone is -0000
[ 1.838746][ T1] gre: GRE over IPv4 demultiplexor driver
[ 1.838754][ T1] IPv4 over IPsec tunneling driver
[ 1.839100][ T1] Initializing XFRM netlink socket
[ 1.839114][ T1] IPsec XFRM device driver
[ 1.839300][ T1] NET: Registered PF_INET6 protocol family
[ 1.840222][ T1] Segment Routing with IPv6
[ 1.840243][ T1] In-situ OAM (IOAM) with IPv6
[ 1.840298][ T1] mip6: Mobile IPv6
[ 1.840612][ T1] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.841085][ T1] NET: Registered PF_PACKET protocol family
[ 1.841098][ T1] NET: Registered PF_KEY protocol family
[ 1.841132][ T1] Bridge firewalling registered
[ 1.841274][ T1] Bluetooth: RFCOMM TTY layer initialized
[ 1.841285][ T1] Bluetooth: RFCOMM socket layer initialized
[ 1.841307][ T1] Bluetooth: RFCOMM ver 1.11
[ 1.841319][ T1] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.841325][ T1] Bluetooth: BNEP filters: protocol multicast
[ 1.841334][ T1] Bluetooth: BNEP socket layer initialized
[ 1.841341][ T1] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.841349][ T1] Bluetooth: HIDP socket layer initialized
[ 1.841370][ T1] l2tp_core: L2TP core driver, V2.0
[ 1.841381][ T1] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.841387][ T1] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.841393][ T1] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.842138][ T1] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 1.842175][ T1] [WLAN_RFKILL]: can’t find rockchip,grf property
[ 1.842183][ T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6275p
[ 1.842190][ T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 1.842197][ T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.842216][ T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 54 flags = 0.
[ 1.842236][ T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 8, flags = 0.
[ 1.842246][ T1] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 1.842253][ T1] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 1.842261][ T1] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 1.842268][ T1] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 1.842984][ T1] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 50.
[ 1.843006][ T1] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 55.
[ 1.843018][ T1] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 60.
[ 1.843031][ T1] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 9.
[ 1.843040][ T1] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
[ 1.843078][ T1] [BT_RFKILL]: Request irq for bt wakeup host
[ 1.843257][ T1] [BT_RFKILL]: ** disable irq
[ 1.843364][ T1] [BT_RFKILL]: bt_default device registered.
[ 1.843453][ T1] input: bt-powerkey as /devices/platform/wireless-bluetooth/input/input5
[ 1.843653][ T1] Key type dns_resolver registered
[ 1.843854][ T1] gyro_icm4260x 7-0068-1: sensor_register_device: icm4260x_gyro, id = 65
[ 1.843864][ T1] i2c i2c-7: sensor_probe: icm42607_gyro,0000000086f6d970
[ 1.843893][ T1] gyro_icm4260x 7-0068-1: sensor_chip_init:icm42607_gyro:devid=0x0,ops=0x00000000212be24b
[ 1.891126][ T1] input: gyro as /devices/platform/2aca0000.i2c/i2c-7/7-0068-1/input/input6
[ 1.891371][ T1] gyro_icm4260x 7-0068-1: sensor_irq_init:use polling,delay=30 ms
[ 1.891583][ T1] gyro_icm4260x 7-0068-1: sensor_misc_device_register:miscdevice: gyrosensor
[ 1.891604][ T1] gyro_icm4260x 7-0068-1: sensor_probe:initialized ok,sensor name:icm4260x_gyro,type:4,id=65
[ 1.891604][ T1]
[ 1.892489][ T1] imx415 4-001a: driver version: 00.01.08
[ 1.892523][ T1] imx415 4-001a: Get hdr mode failed! no hdr default
[ 1.892553][ T1] imx415 4-001a: detect imx415 lane 4
[ 1.892635][ T1] imx415 4-001a: Failed to get power-gpios
[ 1.892657][ T1] imx415 4-001a: could not get default pinstate
[ 1.892673][ T1] imx415 4-001a: could not get sleep pinstate
[ 1.892730][ T1] imx415 4-001a: supply dvdd not found, using dummy regulator
[ 1.892903][ T1] imx415 4-001a: supply dovdd not found, using dummy regulator
[ 1.964179][ T1] imx415 4-001a: Unexpected sensor id(000000), ret(-5)
[ 1.965913][ T1] sc4336 4-0030: driver version: 00.01.01
[ 1.966032][ T1] sc4336 4-0030: could not get default pinstate
[ 1.966052][ T1] sc4336 4-0030: could not get sleep pinstate
[ 1.966261][ T1] sc4336 4-0030: supply dovdd not found, using dummy regulator
[ 1.966406][ T1] sc4336 4-0030: supply dvdd not found, using dummy regulator
[ 1.976542][ T1] sc4336 4-0030: Unexpected sensor id(000000), ret(-5)
[ 1.977702][ T1] registered taskstats version 1
[ 1.977734][ T1] Loading compiled-in X.509 certificates
[ 1.977800][ T1] Key type .fscrypt registered
[ 1.977808][ T1] Key type fscrypt-provisioning registered
[ 1.977977][ T1] pstore: Using crash dump compression: deflate
[ 1.978742][ T1] rga2 27920000.rga: Adding to iommu group 2
[ 1.979345][ T1] rga2 27920000.rga: probe successfully, irq = 49, hw_version:3.e.19357
[ 1.979531][ T1] rga2 27930000.rga: Adding to iommu group 3
[ 1.980003][ T1] rga2 27930000.rga: probe successfully, irq = 50, hw_version:3.e.19357
[ 1.980337][ T1] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
[ 1.980581][ T1] rga: Module initialized. v1.3.3
[ 2.014464][ T143] rockchip-csi2-dphy csi2-dcphy0: csi2 dphy0 probe successfully!
[ 2.016027][ T143] mpp-iep2 27960000.iep: Adding to iommu group 4
[ 2.016386][ T143] mpp-iep2 27960000.iep: probe device
[ 2.016610][ T143] mpp-iep2 27960000.iep: reset_group->rw_sem_on=0
[ 2.016630][ T143] mpp-iep2 27960000.iep: reset_group->rw_sem_on=0
[ 2.016648][ T143] mpp-iep2 27960000.iep: reset_group->rw_sem_on=0
[ 2.016694][ T143] mpp-iep2 27960000.iep: allocate roi buffer failed
[ 2.016728][ T143] mpp-iep2 27960000.iep: probing finish
[ 2.017003][ T143] mpp_jpgdec 27910000.jpegd: Adding to iommu group 1
[ 2.017261][ T143] mpp_jpgdec 27910000.jpegd: probe device
[ 2.017466][ T143] mpp_jpgdec 27910000.jpegd: reset_group->rw_sem_on=0
[ 2.017486][ T143] mpp_jpgdec 27910000.jpegd: reset_group->rw_sem_on=0
[ 2.017593][ T143] mpp_jpgdec 27910000.jpegd: probing finish
[ 2.017890][ T143] mpp_jpgenc 27910800.jpege: Adding to iommu group 1
[ 2.017963][ T143] mpp_jpgenc 27910800.jpege: probe device
[ 2.018147][ T143] mpp_jpgenc 27910800.jpege: reset_group->rw_sem_on=0
[ 2.018162][ T143] mpp_jpgenc 27910800.jpege: reset_group->rw_sem_on=0
[ 2.018218][ T143] mpp_jpgenc 27910800.jpege: probe finish
[ 2.018542][ T143] mpp_rkvdec2 27b00100.rkvdec: Adding to iommu group 7
[ 2.018888][ T143] mpp_rkvdec2 27b00100.rkvdec: rkvdec, probing start
[ 2.019160][ T143] mpp_rkvdec2 27b00100.rkvdec: shared_niu_a is not found!
[ 2.019173][ T143] rkvdec2_init:1197: No niu aclk reset resource define
[ 2.019185][ T143] mpp_rkvdec2 27b00100.rkvdec: shared_niu_h is not found!
[ 2.019195][ T143] rkvdec2_init:1200: No niu hclk reset resource define
[ 2.019213][ T143] mpp_rkvdec2 27b00100.rkvdec: shared_video_cabac is not found!
[ 2.019223][ T143] rkvdec2_init:1206: No cabac reset resource define
[ 2.019275][ T143] mpp_rkvdec2 27b00100.rkvdec: no regulator, devfreq is disabled
[ 2.019476][ T143] mpp_rkvdec2 27b00100.rkvdec: sram_start 0x000000003ff88000
[ 2.019490][ T143] mpp_rkvdec2 27b00100.rkvdec: rcb_iova 0x0000000010000000
[ 2.019501][ T143] mpp_rkvdec2 27b00100.rkvdec: sram_size 491520
[ 2.019512][ T143] mpp_rkvdec2 27b00100.rkvdec: rcb_size 491520
[ 2.019524][ T143] mpp_rkvdec2 27b00100.rkvdec: min_width 512
[ 2.019561][ T143] mpp_rkvdec2 27b00100.rkvdec: link mode probe finish
[ 2.019620][ T143] mpp_rkvdec2 27b00100.rkvdec: probing finish
[ 2.019643][ T143] mpp_rkvdec2 27b00100.rkvdec: probing finish
[ 2.020003][ T143] mpp_rkvenc2 27a00000.rkvenc-core: Adding to iommu group 5
[ 2.020343][ T143] mpp_rkvenc2 27a00000.rkvenc-core: probing start
[ 2.020588][ T143] mpp_rkvenc2 27a00000.rkvenc-core: failed to init opp info
[ 2.020601][ T143] mpp_rkvenc2 27a00000.rkvenc-core: failed to init_opp_table
[ 2.020611][ T143] rkvenc_init:2117: failed to add venc devfreq
[ 2.020678][ T143] mpp_rkvenc2 27a00000.rkvenc-core: attach ccu as core 0
[ 2.020730][ T143] mpp_rkvenc2 27a00000.rkvenc-core: probing finish
[ 2.021014][ T143] mpp_rkvenc2 27a10000.rkvenc-core: Adding to iommu group 6
[ 2.021275][ T143] mpp_rkvenc2 27a10000.rkvenc-core: probing start
[ 2.021504][ T143] mpp_rkvenc2 27a10000.rkvenc-core: failed to init opp info
[ 2.021516][ T143] mpp_rkvenc2 27a10000.rkvenc-core: failed to init_opp_table
[ 2.021526][ T143] rkvenc_init:2117: failed to add venc devfreq
[ 2.021608][ T143] mpp_rkvenc2 27a10000.rkvenc-core: attach ccu as core 1
[ 2.021661][ T143] mpp_rkvenc2 27a10000.rkvenc-core: probing finish
[ 2.021941][ T143] mpp_vdpp 27961000.vdpp: Adding to iommu group 4
[ 2.022005][ T143] mpp_vdpp 27961000.vdpp: probe device
[ 2.022171][ T143] mpp_vdpp 27961000.vdpp: reset_group->rw_sem_on=0
[ 2.022186][ T143] mpp_vdpp 27961000.vdpp: reset_group->rw_sem_on=0
[ 2.022199][ T143] mpp_vdpp 27961000.vdpp: reset_group->rw_sem_on=0
[ 2.022248][ T143] mpp_vdpp 27961000.vdpp: probing finish
[ 2.022533][ T143] rockchip-vop2 27d00000.vop: Adding to iommu group 11
[ 2.023059][ T143] OF: graph: no port node found in /dp@27e40000
[ 2.024944][ T143] panel-simple-dsi 27d80000.dsi.0: Expected bpc in {6,8} but got: 0
[ 2.025665][ T143] rockchip-vop2 27d00000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x4, primary plane phy id: 2
[ 2.025692][ T143] rockchip-vop2 27d00000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x8, primary plane phy id: 3
[ 2.025705][ T143] rockchip-vop2 27d00000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x100, primary plane phy id: 8
[ 2.026066][ T143] [drm] unsupported AFBC format[3231564e]
[ 2.026473][ T143] rockchip-vop2 27d00000.vop: bin=0
[ 2.026679][ T143] rockchip-vop2 27d00000.vop: leakage=0
[ 2.027558][ T143] rockchip-vop2 27d00000.vop: avs=0
[ 2.027639][ T143] rockchip-vop2 27d00000.vop: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 2.027665][ T143] debugfs: Directory ‘vdd_logic_s0’ with parent ‘vdd_logic_s0’ already present!
[ 2.029743][ T143] rockchip-vop2 27d00000.vop: Supported VOP aclk dvfs, normal mode:500000000, reset mode:594000000, advanced mode:702000000
[ 2.029763][ T143] rockchip-drm display-subsystem: bound 27d00000.vop (ops vop2_component_ops)
[ 2.030946][ T143] dwhdmi-rockchip 27da0000.hdmi: registered ddc I2C bus driver
[ 2.031800][ T143] rockchip-drm display-subsystem: bound 27da0000.hdmi (ops dw_hdmi_rockchip_ops)
[ 2.031875][ T143] rockchip-drm display-subsystem: bound 27d80000.dsi (ops dw_mipi_dsi2_ops)
[ 2.032287][ T143] rockchip-drm display-subsystem: bound 27e40000.dp (ops dw_dp_component_ops)
[ 2.033136][ T143] rockchip-drm display-subsystem: route-hdmi: failed to get logo,offset
[ 2.049100][ T143] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.7.auto: dw_hdcp_qp_hdcp_probe success
[ 2.049513][ T143] [drm] Initialized rockchip 4.0.0 20140818 for display-subsystem on minor 0
[ 2.054844][ T143] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
上面这段是显示相关的初始化，只有DRM正常初始化后正常显示框架才能正常启动，如果出现panel或者dp或者HDMI初始化失败就会导致drm初始化失败，从而导致android层surfaceflinger初始化失败，出现这种情况可以先尝试把报错的显示设备(dsi/dp/hdmi)dts中disabled

[ 2.055492][ T80] mali 27800000.gpu: Kernel DDK version g21p0-01eac0
[ 2.055612][ T80] mali 27800000.gpu: GPU metrics tracepoint support enabled
[ 2.055836][ T80] mali 27800000.gpu: bin=0
[ 2.056028][ T80] mali 27800000.gpu: leakage=0
[ 2.056048][ T80] debugfs: Directory ‘27800000.gpu-mali’ with parent ‘vdd_gpu_s0’ already present!
[ 2.057802][ T80] mali 27800000.gpu: pvtm=807
[ 2.058343][ T80] mali 27800000.gpu: pvtm-volt-sel=1
[ 2.058380][ T80] debugfs: Directory ‘27800000.gpu-mali’ with parent ‘vdd_gpu_s0’ already present!
[ 2.059078][ T80] mali 27800000.gpu: avs=0
上面这段是GPU的初始化，包括DDK版本信息，如果这里初始失败或者DDK版本和android上层的不匹配就会导致android层surfaceflinger初始化失败，出现这种情况可以检查GPU驱动或者DDK版本
[ 2.059103][ T80] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 144; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 2.060787][ T80] mali 27800000.gpu: Register LUT 00070200 initialized for GPU arch 0x00070400
[ 2.060817][ T143] input: adc-keys as /devices/platform/adc-keys/input/input7
[ 2.060817][ T80] mali 27800000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 2.060936][ T80] mali 27800000.gpu: No priority control manager is configured
[ 2.060946][ T80] mali 27800000.gpu: Large page allocation set to false after hardware feature check
[ 2.061169][ T80] mali 27800000.gpu: No memory group manager is configured
[ 2.061743][ T8] <>[gt1x_ts_probe:560] GTP Driver Version: V1.4<2015/07/10>
[ 2.061758][ T8] <>[gt1x_ts_probe:561] GTP I2C Address: 0x14
[ 2.061807][ T8] <>[gt1x_parse_dt:341] vdd_ana not specified, fallback to power-supply
[ 2.061997][ T80] mali 27800000.gpu: EM: created perf domain
[ 2.062083][ T8] <>[gt1x_parse_dt:348] Power Invert,no
[ 2.062195][ T8] <>[gt1x_reset_guitar:788] GTP RESET!
[ 2.062321][ T80] mali 27800000.gpu: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 2.063709][ T80] mali 27800000.gpu: * MALI kbase_mmap_min_addr compiled to CONFIG_DEFAULT_MMAP_MIN_ADDR, no runtime update possible! *
[ 2.063721][ T80] mali 27800000.gpu: Probed as mali0
[ 2.075651][ T143] rockchip-dmc dmc: bin=0
[ 2.075849][ T143] rockchip-dmc dmc: leakage=0
[ 2.077762][ T143] rockchip-dmc dmc: avs=0
[ 2.077785][ T143] rockchip-dmc dmc: current ATF version 0x100
[ 2.078001][ T143] rockchip-dmc dmc: normal_rate = 1560000000
[ 2.078010][ T143] rockchip-dmc dmc: reboot_rate = 2112000000
[ 2.078018][ T143] rockchip-dmc dmc: suspend_rate = 528000000
[ 2.078026][ T143] rockchip-dmc dmc: video_4k_rate = 1560000000
[ 2.078034][ T143] rockchip-dmc dmc: video_4k_10b_rate = 1560000000
[ 2.078043][ T143] rockchip-dmc dmc: video_svep_rate = 1560000000
[ 2.078050][ T143] rockchip-dmc dmc: boost_rate = 2112000000
[ 2.078058][ T143] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 2112000000
[ 2.078066][ T143] rockchip-dmc dmc: performance_rate = 2112000000
[ 2.078074][ T143] rockchip-dmc dmc: hdmirx_rate = 2112000000
[ 2.078082][ T143] rockchip-dmc dmc: deep_suspend_rate = 2112000000
[ 2.078094][ T143] rockchip-dmc dmc: failed to get vop pn to msch rl
[ 2.078397][ T143] rockchip-dmc dmc: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
上面这段是DDR变频的初始化，DDR变频如果没有初始化需要检查一下dts中是否有打开dmc和dfi节点，如果有开在检查硬件供电是否正常
[ 2.078429][ T143] debugfs: Directory ‘vdd_logic_s0’ with parent ‘vdd_logic_s0’ already present!
[ 2.083806][ T143] debugfs: File ‘Capture’ in directory ‘dapm’ already present!
[ 2.084963][ T143] input: rockchip-dp0 rockchip-dp0 as /devices/platform/dp0-sound/sound/card1/input8
[ 2.088078][ T143] input: rockchip-hdmi rockchip-hdmi as /devices/platform/hdmi-sound/sound/card2/input9
[ 2.089983][ T1] rkcif rkcif-mipi-lvds: clear unready subdev num: 5
[ 2.090620][ T1] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.090641][ T1] rkcif-mipi-lvds: Async subdev notifier completed
[ 2.090653][ T1] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.090661][ T1] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
[ 2.090719][ T128] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.090730][ T128] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
[ 2.092311][ T1] RKNPU 27700000.npu: Adding to iommu group 0
[ 2.092611][ T1] RKNPU 27700000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 2.092967][ T1] RKNPU 27700000.npu: can’t request region for resource [mem 0x27700000-0x27707fff]
[ 2.093008][ T1] RKNPU 27700000.npu: can’t request region for resource [mem 0x27708000-0x2770ffff]
[ 2.093561][ T1] [drm] Initialized rknpu 0.9.7 20240424 for 27700000.npu on minor 1
[ 2.095133][ T1] RKNPU 27700000.npu: bin=0
[ 2.095401][ T1] RKNPU 27700000.npu: leakage=0
[ 2.095437][ T1] debugfs: Directory ‘27700000.npu-rknpu’ with parent ‘vdd_npu_s0’ already present!
[ 2.097267][ T1] RKNPU 27700000.npu: pvtm=827
[ 2.097865][ T1] RKNPU 27700000.npu: pvtm-volt-sel=2
[ 2.097927][ T1] debugfs: Directory ‘27700000.npu-rknpu’ with parent ‘vdd_npu_s0’ already present!
[ 2.099015][ T1] RKNPU 27700000.npu: avs=0
[ 2.099344][ T1] RKNPU 27700000.npu: EM: created perf domain
[ 2.099619][ T1] RKNPU 27700000.npu: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 2.101091][ T1] RKNPU 27700000.npu: RKNPU: nbuf region: [0x000000003fe80000, 0x000000003ff80000), nbuf size: 0x100000
上面这段是NPU及NPU变频的初始化
[ 2.103110][ T1] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.103903][ T1] cfg80211: Loaded X.509 cert ‘wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600’
[ 2.104262][ T1] cfg80211: Loaded X.509 cert ‘sforshee: 00b28ddf47aef9cea7’
[ 2.104375][ T32] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.104391][ T32] cfg80211: failed to load regulatory.db
[ 2.105892][ T1] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 2.107341][ T1] rockchip-suspend not set sleep-mode-config for mem-lite
[ 2.107355][ T1] rockchip-suspend not set wakeup-config for mem-lite
[ 2.107364][ T1] rockchip-suspend not set sleep-mode-config for mem-ultra
[ 2.107371][ T1] rockchip-suspend not set wakeup-config for mem-ultra
[ 2.108558][ T1] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 411; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is ‘’, rk_ko_ver is ‘5’, built .
[ 2.109064][ T1] Mali:
[ 2.109067][ T1] Mali device driver loaded
[ 2.109085][ T1] rkisp rkisp-vir0: clear unready subdev num: 1
[ 2.109302][ T1] rkisp-vir0: Async subdev notifier completed
[ 2.109315][ T1] ALSA device list:
[ 2.109323][ T1] #0: rockchip-es8388
[ 2.109330][ T1] #1: rockchip-dp0
[ 2.109337][ T1] #2: rockchip-hdmi
[ 2.157635][ T8] <>[gt1x_get_chip_type:907] Chip Type: GT1X
[ 2.167101][ T8] <>[gt1x_read_version:863] IC VERSION:GT1158_00012A(Patch)_0102(Mask)_00(SensorID)
[ 2.167137][ T8] <>[gt1x_init_panel:606] Config group0 used, length:239
[ 2.167157][ T8] <>[gt1x_init_panel:657] X_MAX=720,Y_MAX=1280,TRIGGER=0x01,WAKEUP_LEVEL=1
[ 2.398767][ T8] input: goodix-ts as /devices/virtual/input/input10
[ 2.400463][ T1] Freeing unused kernel memory: 1856K

从这里开始进入init阶段
[ 2.400644][ T1] Run /init as init process
[ 2.404408][ T1] init: init first stage started!
[ 2.404648][ T1] init: Unable to open /lib/modules, skipping module loading.
[ 2.404964][ T1] init: Copied ramdisk prop to /second_stage_resources/system/etc/ramdisk/build.prop
[ 2.405502][ T1] init: [libfs_mgr] ReadFstabFromDt(): failed to read fstab from dt
[ 2.407475][ T1] init: Using Android DT directory /proc/device-tree/firmware/android/
[ 2.407583][ T1] init: Failed to read vbmeta partitions.
[ 2.486461][ T1] init: [libfs_mgr] Not running /system/bin/fsck.f2fs on /dev/block/sda11 (executable not in system image)
[ 2.490058][ T1] F2FS-fs (sda11): Found nat_bits in checkpoint
[ 2.495116][ T1] F2FS-fs (sda11): Mounted with checkpoint version = 4fc2a131
[ 2.495240][ T1] init: [libfs_mgr] __mount(source=/dev/block/by-name/metadata,target=/metadata,type=f2fs)=0: Success
[ 2.496470][ T1] init: Failed to copy /avb into /metadata/gsi/dsu/avb/: No such file or directory
[ 2.498640][ T1] init: [libfs_mgr] Created logical partition system on device /dev/block/dm-0
[ 2.505138][ T1] erofs: (device dm-0): erofs_read_superblock: cannot find valid erofs superblock
[ 2.507423][ T1] EXT4-fs (dm-0): mounted filesystem without journal. Quota mode: none.
[ 2.510615][ T1] erofs: (device dm-3): erofs_read_superblock: cannot find valid erofs superblock
[ 2.512457][ T1] EXT4-fs (dm-3): mounted filesystem without journal. Quota mode: none.
[ 2.513337][ T1] erofs: (device dm-5): erofs_read_superblock: cannot find valid erofs superblock
[ 2.514928][ T1] EXT4-fs (dm-5): mounted filesystem without journal. Quota mode: none.
[ 2.515852][ T1] erofs: (device dm-1): erofs_read_superblock: cannot find valid erofs superblock
[ 2.517169][ T1] EXT4-fs (dm-1): mounted filesystem without journal. Quota mode: none.
[ 2.517857][ T1] erofs: (device dm-2): erofs_read_superblock: cannot find valid erofs superblock
[ 2.519297][ T1] EXT4-fs (dm-2): mounted filesystem without journal. Quota mode: none.
[ 2.520028][ T1] erofs: (device dm-4): erofs_read_superblock: cannot find valid erofs superblock
[ 2.521359][ T1] EXT4-fs (dm-4): mounted filesystem without journal. Quota mode: none.
[ 2.522175][ T1] erofs: (device dm-6): erofs_read_superblock: cannot find valid erofs superblock
[ 2.523548][ T1] EXT4-fs (dm-6): mounted filesystem without journal. Quota mode: none.
[ 2.524287][ T1] erofs: (device dm-7): erofs_read_superblock: cannot find valid erofs superblock
[ 2.525606][ T1] EXT4-fs (dm-7): mounted filesystem without journal. Quota mode: none.
[ 2.539382][ T1] printk: init: 34 output lines suppressed due to ratelimiting
[ 2.632805][ T1] init: Opening SELinux policy
[ 2.634352][ T1] init: Falling back to standard signature check. TODO implement support for fsverity SEPolicy.
[ 2.634411][ T1] init: Error: Apex SEPolicy failed signature check
[ 2.634425][ T1] init: Loading APEX Sepolicy from /system/etc/selinux/apex/SEPolicy.zip
[ 2.634447][ T1] init: Failed to open package /system/etc/selinux/apex/SEPolicy.zip: No such file or directory
[ 2.640100][ T1] init: Loading SELinux policy
[ 2.655734][ T1] SELinux: Permission bpf in class capability2 not defined in policy.
[ 2.655766][ T1] SELinux: Permission checkpoint_restore in class capability2 not defined in policy.
[ 2.655784][ T1] SELinux: Permission bpf in class cap2_userns not defined in policy.
[ 2.655791][ T1] SELinux: Permission checkpoint_restore in class cap2_userns not defined in policy.
[ 2.655854][ T1] SELinux: Class mctp_socket not defined in policy.
[ 2.655867][ T1] SELinux: Class user_namespace not defined in policy.
[ 2.655874][ T1] SELinux: the above unknown classes and permissions will be denied
[ 2.660984][ T1] SELinux: policy capability network_peer_controls=1
[ 2.661017][ T1] SELinux: policy capability open_perms=1
[ 2.661024][ T1] SELinux: policy capability extended_socket_class=1
[ 2.661031][ T1] SELinux: policy capability always_check_network=0
[ 2.661038][ T1] SELinux: policy capability cgroup_seclabel=0
[ 2.661044][ T1] SELinux: policy capability nnp_nosuid_transition=1
[ 2.661051][ T1] SELinux: policy capability genfs_seclabel_symlinks=0
[ 2.661057][ T1] SELinux: policy capability ioctl_skip_cloexec=0
[ 2.978491][ T68] audit: type=1403 audit(1717467508.860:2): auid=4294967295 ses=4294967295 lsm=selinux res=1
[ 2.987003][ T1] selinux: SELinux: Loaded file context from:
[ 2.987058][ T1] selinux: /system/etc/selinux/plat_file_contexts
[ 2.987080][ T1] selinux: /system_ext/etc/selinux/system_ext_file_contexts
[ 2.987100][ T1] selinux: /vendor/etc/selinux/vendor_file_contexts
[ 2.992529][ T1] printk: init: 1 output lines suppressed due to ratelimiting
[ 3.008961][ T1] init: init second stage started!
[ 3.026111][ T1] selinux: SELinux: Loaded file context from:
[ 3.026147][ T1] selinux: /system/etc/selinux/plat_file_contexts
[ 3.026156][ T1] selinux: /system_ext/etc/selinux/system_ext_file_contexts
[ 3.026164][ T1] selinux: /vendor/etc/selinux/vendor_file_contexts
[ 3.042060][ T1] init: Using Android DT directory /proc/device-tree/firmware/android/
[ 3.047071][ T68] audit: type=1107 audit(1717467508.928:3): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg=‘avc: denied { set } for property=ro.flash_img.enable pid=1 uid=0 gid=0 sco’
[ 3.047293][ T68] audit: type=1107 audit(1717467508.928:4): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg=‘avc: denied { set } for property=ro.ril.ecclist pid=1 uid=0 gid=0 scontext’
[ 3.047538][ T68] audit: type=1107 audit(1717467508.928:5): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg=‘avc: denied { set } for property=wifi.supplicant_scan_interval pid=1 uid=0’
[ 3.047803][ T68] audit: type=1107 audit(1717467508.928:6): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg=‘avc: denied { set } for property=ro.boot.vr pid=1 uid=0 gid=0 scontext=u:r’
[ 3.052371][ T1] init: Setting product property ro.product.brand to ‘rockchip’ (from ro.product.product.brand)
[ 3.052413][ T1] init: Setting product property ro.product.device to ‘rk3576_u’ (from ro.product.product.device)
[ 3.052446][ T1] init: Setting product property ro.product.manufacturer to ‘rockchip’ (from ro.product.product.manufacturer)
[ 3.052469][ T1] init: Setting product property ro.product.model to ‘rk3576_u’ (from ro.product.product.model)
[ 3.081087][ T68] audit: type=1107 audit(1717467508.960:7): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg=‘avc: denied { read } for property=flash.success pid=0 uid=0 gid=0 scontext’
[ 3.118547][ T1] cgroup: Unknown subsys name ‘memoryapps’
[ 3.118706][ T1] cgroup: Unknown subsys name ‘schedtune’
[ 3.174401][ T205] ueventd: ueventd started!
[ 3.177227][ T205] selinux: SELinux: Loaded file context from:
[ 3.177263][ T205] selinux: /system/etc/selinux/plat_file_contexts
[ 3.177272][ T205] selinux: /system_ext/etc/selinux/system_ext_file_contexts
[ 3.177281][ T205] selinux: /vendor/etc/selinux/vendor_file_contexts
[ 3.177808][ T205] ueventd: Parsing file /system/etc/ueventd.rc…
[ 3.178212][ T205] ueventd: Added ‘/vendor/etc/ueventd.rc’ to import list
[ 3.178235][ T205] ueventd: Added ‘/odm/etc/ueventd.rc’ to import list
[ 3.178623][ T205] ueventd: Parsing file /vendor/etc/ueventd.rc…
[ 3.178984][ T205] ueventd: Added ‘/vendor/etc/ueventd.car.rc’ to import list
[ 3.201933][ T206] apexd: Bootstrap subcommand detected
[ 3.202310][ T206] cutils-trace: Error opening trace file: No such file or directory (2)
[ 3.202838][ T206] apexd-bootstrap: Scanning /system/apex for pre-installed ApexFiles
[ 3.203842][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.sdkext.apex
[ 3.206226][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.btservices.apex
[ 3.208343][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.os.statsd.apex
[ 3.210351][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.devicelock.apex
[ 3.212254][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.ipsec.capex
[ 3.214954][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.ondevicepersonalization.capex
[ 3.217651][ T206] apexd-bootstrap: Found pre-installed APEX /system/apex/com.android.tethering.capex
[ 3.406198][ T68] audit: type=1400 audit(1717467509.288:8): avc: denied { create } for pid=66 comm=“kdevtmpfs” name=“loop16” scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk_file perm1
[ 3.406232][ T68] audit: type=1400 audit(1717467509.288:9): avc: denied { setattr } for pid=66 comm=“kdevtmpfs” name=“loop16” dev=“devtmpfs” ino=209 scontext=u:r:kernel:s0 tcontext=u:object_r:device1
[ 3.438387][ T248] loop0: detected capacity change from 0 to 71832
[ 3.438952][ T250] loop1: detected capacity change from 0 to 13984
[ 3.439430][ T249] loop2: detected capacity change from 0 to 49776
[ 3.440135][ T251] loop3: detected capacity change from 0 to 1616
[ 3.476296][ T251] EXT4-fs (loop3): mounted filesystem without journal. Quota mode: none.
[ 3.478195][ T249] EXT4-fs (loop2): mounted filesystem without journal. Quota mode: none.
[ 3.478270][ T250] EXT4-fs (loop1): mounted filesystem without journal. Quota mode: none.
[ 3.478301][ T248] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: none.
[ 3.486484][ T206] printk: apexd: 43 output lines suppressed due to ratelimiting
[ 3.547111][ T68] audit: type=1400 audit(1717467509.428:10): avc: denied { mounton } for pid=1 comm=“init” path=“/sys/kernel/debug/tracing” dev=“debugfs” ino=2255 scontext=u:r:init:s0 tcontext=u:obj1
[ 3.761057][ T1] Registered swp emulation handler
[ 3.800211][ T274] servicemanager: Starting sm instance on /dev/binder
[ 3.805198][ T272] logd.auditd: start
[ 3.805241][ T272] logd.klogd: 2811700667
[ 3.805295][ T274] SELinux: SELinux: Loaded service context from:
[ 3.805350][ T274] SELinux: /system/etc/selinux/plat_service_contexts
[ 3.805382][ T274] SELinux: /system_ext/etc/selinux/system_ext_service_contexts
[ 3.805407][ T274] SELinux: /vendor/etc/selinux/vendor_service_contexts
[ 3.813334][ T272] logd: Loaded bug_map file: /system_ext/etc/selinux/bug_map
[ 3.813439][ T272] logd: Loaded bug_map file: /vendor/etc/selinux/selinux_denial_metadata
[ 3.813791][ T272] logd: Loaded bug_map file: /system/etc/selinux/bug_map
[ 3.814517][ T276] vndservicemanager: Starting sm instance on /dev/vndbinder
[ 3.815351][ T276] SELinux: SELinux: Loaded vndservice context from:
[ 3.815367][ T276] SELinux: /vendor/etc/selinux/vndservice_contexts
console:/ $ [ 3.844433][ T289] type=1400 audit(1717467509.724:12): avc: denied { write } for comm=“tee-supplicant” name=“property_service” dev=“tmpfs” ino=366 scontext=u:r:tee:s0 tcontext=u:object_r:1
[ 3.844511][ T289] type=1400 audit(1717467509.724:13): avc: denied { connectto } for comm=“tee-supplicant” path=“/dev/socket/property_service” scontext=u:r:tee:s0 tcontext=u:r:init:s0 tclass=unix_str1
[ 3.844751][ T289] type=1107 audit(1717467509.724:14): uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg=‘avc: denied { set } for property=vendor.security.tee_supplicant pid=286 uid=0 gid=0 sc’
[ 3.849891][ T1] EXT4-fs: Ignoring removed nomblk_io_submit option
[ 3.870131][ T1] EXT4-fs (sda10): mounted filesystem with ordered data mode. Quota mode: none.
[ 3.870619][ T1] EXT4-fs (sda10): unmounting filesystem.
[ 3.902984][ T1] e2fsck: e2fsck 1.46.6 (1-Feb-2023)
[ 3.906434][ T1] e2fsck: /dev/block/by-name/cache: clean, 19/98304 files, 16449/98304 blocks
[ 3.911800][ T1] EXT4-fs (sda10): mounted filesystem with ordered data mode. Quota mode: none.
[ 3.917148][ T289] type=1400 audit(1717467509.796:15): avc: denied { create } for comm=“kdevtmpfs” name=“dm-40” scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk_file permissive=1
[ 3.917241][ T289] type=1400 audit(1717467509.796:16): avc: denied { setattr } for comm=“kdevtmpfs” name=“dm-40” dev=“devtmpfs” ino=229 scontext=u:r:kernel:s0 tcontext=u:object_r:device:s0 tclass=blk1
I/TA: Hello Rockchip Keymaster! ver:20231201 rpmb :0
I/TA: Provision google keybox:no,ID attestation:no
[ 3.940784][ T274] servicemanager: getDeviceHalManifest: Reading VINTF information.
[ 3.944943][ T274] servicemanager: getDeviceHalManifest: Successfully processed VINTF information
[ 3.944989][ T274] servicemanager: getFrameworkHalManifest: Reading VINTF information.
[ 3.947493][ T274] servicemanager: getFrameworkHalManifest: Successfully processed VINTF information
[ 3.947563][ T274] servicemanager: Found android.hardware.security.keymint.IKeyMintDevice/default in device VINTF manifest.
[ 4.061488][ T290] vold: Error getting bootctrl v1.0 module.
[ 4.327115][ T290] fsck.f2fs: Info: Fix the reported corruption.
[ 4.327813][ T290] fsck.f2fs: Info: not exist /proc/version!
[ 4.358167][ T290] fsck.f2fs: Info: MKFS version
[ 4.358195][ T290] fsck.f2fs: “6.1.75”
[ 4.358204][ T290] fsck.f2fs: Info: FSCK version
[ 4.358212][ T290] fsck.f2fs: from “6.1.75”
[ 4.358219][ T290] fsck.f2fs: to “6.1.75”
[ 4.358227][ T290] fsck.f2fs: Info: superblock features = 1499 : encrypt verity extra_attr project_quota quota_ino casefold
[ 4.358235][ T290] fsck.f2fs: Info: superblock encrypt level = 0, salt = 00000000000000000000000000000000
[ 4.358243][ T290] fsck.f2fs: Info: Segments per section = 1
[ 4.403190][ T290] F2FS-fs (dm-40): Using encoding defined by superblock: utf8-12.1.0 with flags 0x0
[ 4.523021][ T290] F2FS-fs (dm-40): Found nat_bits in checkpoint
[ 4.647757][ T290] F2FS-fs (dm-40): Mounted with checkpoint version = 5147d6f8
[ 4.717150][ T1] fscrypt: AES-256-CTS-CBC using implementation “cts-cbc-aes-ce”
[ 4.718072][ T1] fscrypt: AES-256-XTS using blk-crypto-fallback
[ 4.759014][ T290] vold: keystore2 Keystore earlyBootEnded returned service specific error: -68
[ 4.791823][ T375] apexd: Scanning /system/apex for pre-installed ApexFiles
[ 4.792123][ T375] apexd: Found pre-installed APEX /system/apex/com.android.sdkext.apex
[ 4.792768][ T375] apexd: Found pre-installed APEX /system/apex/com.android.btservices.apex
[ 4.793055][ T375] apexd: Found pre-installed APEX /system/apex/com.android.os.statsd.apex
[ 4.793310][ T375] apexd: Found pre-installed APEX /system/apex/com.android.devicelock.apex
[ 4.793578][ T375] apexd: Found pre-installed APEX /system/apex/com.android.ipsec.capex
[ 4.793839][ T375] apexd: Found pre-installed APEX /system/apex/com.android.ondevicepersonalization.capex
[ 4.794081][ T375] apexd: Found pre-installed APEX /system/apex/com.android.tethering.capex
[ 4.794343][ T375] apexd: Found pre-installed APEX /system/apex/com.android.media.swcodec.capex
[ 4.794558][ T375] apexd: Found pre-installed APEX /system/apex/com.android.conscrypt.capex
[ 4.869627][ T154] vendor storage:20190527 ret = -1
[ 4.902576][ T405] loop4: detected capacity change from 0 to 6264
[ 4.922017][ T407] loop5: detected capacity change from 0 to 49896
[ 4.922576][ T406] loop6: detected capacity change from 0 to 2232
[ 4.923495][ T404] loop7: detected capacity change from 0 to 1520
[ 4.923994][ T408] loop8: detected capacity change from 0 to 10472
[ 4.924515][ T409] loop9: detected capacity change from 0 to 22072
[ 4.924966][ T410] loop10: detected capacity change from 0 to 49776
[ 4.925418][ T411] loop11: detected capacity change from 0 to 1616
[ 4.926174][ T412] loop12: detected capacity change from 0 to 536
[ 4.927560][ T413] loop13: detected capacity change from 0 to 13984
[ 4.928265][ T414] loop14: detected capacity change from 0 to 680
[ 4.930598][ T416] loop15: detected capacity change from 0 to 71832
[ 4.931057][ T415] loop16: detected capacity change from 0 to 536
[ 4.931764][ T417] loop17: detected capacity change from 0 to 11504
[ 4.932690][ T419] loop18: detected capacity change from 0 to 9440
[ 4.933451][ T418] loop19: detected capacity change from 0 to 536
[ 4.934415][ T420] loop20: detected capacity change from 0 to 1624
[ 4.936751][ T421] loop21: detected capacity change from 0 to 4672
[ 4.937347][ T422] loop22: detected capacity change from 0 to 35752
[ 4.938324][ T423] loop23: detected capacity change from 0 to 11992
[ 4.939191][ T426] loop24: detected capacity change from 0 to 8184
[ 4.940286][ T425] loop25: detected capacity change from 0 to 17136
[ 4.940964][ T427] loop26: detected capacity change from 0 to 44696
[ 4.941698][ T428] loop27: detected capacity change from 0 to 7312
[ 4.942422][ T429] loop28: detected capacity change from 0 to 8520
[ 4.943151][ T424] loop29: detected capacity change from 0 to 51104
[ 4.943954][ T430] loop30: detected capacity change from 0 to 37008
[ 4.944589][ T431] loop31: detected capacity change from 0 to 66400
[ 4.945506][ T432] loop32: detected capacity change from 0 to 7512
[ 4.946237][ T433] loop33: detected capacity change from 0 to 57160
[ 4.947500][ T434] loop34: detected capacity change from 0 to 536
[ 4.948173][ T435] loop35: detected capacity change from 0 to 19592
[ 4.971496][ T425] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.972562][ T419] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.972705][ T427] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.973364][ T420] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.974768][ T421] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.974787][ T426] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.975606][ T423] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.975832][ T408] EXT4-fs (loop8): mounted filesystem without journal. Quota mode: none.
[ 4.975880][ T410] EXT4-fs (loop10): mounted filesystem without journal. Quota mode: none.
[ 4.976025][ T405] EXT4-fs (loop4): mounted filesystem without journal. Quota mode: none.
[ 4.976385][ T416] EXT4-fs (loop15): mounted filesystem without journal. Quota mode: none.
[ 4.976864][ T409] EXT4-fs (loop9): mounted filesystem without journal. Quota mode: none.
[ 4.977173][ T412] EXT4-fs (loop12): mounted filesystem without journal. Quota mode: none.
[ 4.978545][ T407] EXT4-fs (loop5): mounted filesystem without journal. Quota mode: none.
[ 4.978760][ T414] EXT4-fs (loop14): mounted filesystem without journal. Quota mode: none.
[ 4.978853][ T413] EXT4-fs (loop13): mounted filesystem without journal. Quota mode: none.
[ 4.978924][ T406] EXT4-fs (loop6): mounted filesystem without journal. Quota mode: none.
[ 4.979488][ T411] EXT4-fs (loop11): mounted filesystem without journal. Quota mode: none.
[ 4.983177][ T429] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.983177][ T428] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.983177][ T424] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.984351][ T432] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.984351][ T431] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.984351][ T434] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.984512][ T433] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.984545][ T418] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.984703][ T422] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.985364][ T404] EXT4-fs (loop7): mounted filesystem without journal. Quota mode: none.
[ 4.987133][ T415] EXT4-fs (loop16): mounted filesystem without journal. Quota mode: none.
[ 4.987292][ T417] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.988647][ T430] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 4.995797][ T427] EXT4-fs (dm-20): mounting with “discard” option, but the device does not support discard
[ 4.995826][ T427] EXT4-fs (dm-20): mounted filesystem without journal. Quota mode: none.
[ 4.995853][ T419] EXT4-fs (dm-35): mounting with “discard” option, but the device does not support discard
[ 4.995863][ T419] EXT4-fs (dm-35): mounted filesystem without journal. Quota mode: none.
[ 4.998884][ T423] EXT4-fs (dm-30): mounting with “discard” option, but the device does not support discard
[ 4.998901][ T423] EXT4-fs (dm-30): mounted filesystem without journal. Quota mode: none.
[ 5.000276][ T435] device-mapper: verity: sha256 using implementation “sha256-ce”
[ 5.001061][ T425] EXT4-fs (dm-27): mounting with “discard” option, but the device does not support discard
[ 5.001087][ T425] EXT4-fs (dm-27): mounted filesystem without journal. Quota mode: none.
[ 5.021046][ T420] EXT4-fs (dm-33): mounting with “discard” option, but the device does not support discard
[ 5.021068][ T420] EXT4-fs (dm-33): mounted filesystem without journal. Quota mode: none.
[ 5.021101][ T426] EXT4-fs (dm-21): mounting with “discard” option, but the device does not support discard
[ 5.021110][ T426] EXT4-fs (dm-21): mounted filesystem without journal. Quota mode: none.
[ 5.021306][ T421] EXT4-fs (dm-32): mounting with “discard” option, but the device does not support discard
[ 5.021340][ T421] EXT4-fs (dm-32): mounted filesystem without journal. Quota mode: none.
[ 5.027464][ T424] EXT4-fs (dm-29): mounting with “discard” option, but the device does not support discard
[ 5.027484][ T424] EXT4-fs (dm-29): mounted filesystem without journal. Quota mode: none.
[ 5.047883][ T428] EXT4-fs (dm-17): mounting with “discard” option, but the device does not support discard
[ 5.047883][ T429] EXT4-fs (dm-25): mounting with “discard” option, but the device does not support discard
[ 5.047895][ T428] EXT4-fs (dm-17): mounted filesystem without journal. Quota mode: none.
[ 5.047925][ T429] EXT4-fs (dm-25): mounted filesystem without journal. Quota mode: none.
[ 5.049368][ T433] EXT4-fs (dm-14): mounting with “discard” option, but the device does not support discard
[ 5.049387][ T433] EXT4-fs (dm-14): mounted filesystem without journal. Quota mode: none.
[ 5.050285][ T434] EXT4-fs (dm-12): mounting with “discard” option, but the device does not support discard
[ 5.050313][ T434] EXT4-fs (dm-12): mounted filesystem without journal. Quota mode: none.
[ 5.070771][ T422] EXT4-fs (dm-31): mounting with “discard” option, but the device does not support discard
[ 5.070771][ T431] EXT4-fs (dm-22): mounting with “discard” option, but the device does not support discard
[ 5.070779][ T422] EXT4-fs (dm-31): mounted filesystem without journal. Quota mode: none.
[ 5.070789][ T431] EXT4-fs (dm-22): mounted filesystem without journal. Quota mode: none.
[ 5.070884][ T417] EXT4-fs (dm-37): mounting with “discard” option, but the device does not support discard
[ 5.070906][ T417] EXT4-fs (dm-37): mounted filesystem without journal. Quota mode: none.
[ 5.070914][ T418] EXT4-fs (dm-34): mounting with “discard” option, but the device does not support discard
[ 5.070924][ T418] EXT4-fs (dm-34): mounted filesystem without journal. Quota mode: none.
[ 5.071276][ T432] EXT4-fs (dm-15): mounting with “discard” option, but the device does not support discard
[ 5.071301][ T432] EXT4-fs (dm-15): mounted filesystem without journal. Quota mode: none.
[ 5.091952][ T430] EXT4-fs (dm-24): mounting with “discard” option, but the device does not support discard
[ 5.091983][ T430] EXT4-fs (dm-24): mounted filesystem without journal. Quota mode: none.
[ 5.104128][ T435] EXT4-fs (dm-8): mounting with “discard” option, but the device does not support discard
[ 5.104160][ T435] EXT4-fs (dm-8): mounted filesystem without journal. Quota mode: none.
[ 5.518750][ T503] fs-verity: sha256 using implementation “sha256-ce”
[ 5.691923][ T506] apexd: Snapshot DE subcommand detected
[ 5.693349][ T506] apexd-snapshotde: Marking APEXd as ready
[ 5.748539][ T510] WARNING: Unprivileged eBPF is enabled, data leaks possible via Spectre v2 BHB attacks!
[ 5.750336][ T510] LibBpfLoader: Section bpfloader_min_ver value is 2 [0x2]
[ 5.750385][ T510] LibBpfLoader: Section bpfloader_max_ver value is 25 [0x19]
[ 5.750457][ T510] LibBpfLoader: Section size_of_bpf_map_def value is 120 [0x78]
[ 5.750497][ T510] LibBpfLoader: Section size_of_bpf_prog_def value is 92 [0x5c]
[ 5.750507][ T510] LibBpfLoader: BpfLoader version 0x00026 ignoring ELF object /apex/com.android.tethering/etc/bpf/test.o with max ver 0x00019
[ 5.750530][ T510] bpfloader: Loaded object: /apex/com.android.tethering/etc/bpf/test.o
[ 5.752377][ T510] LibBpfLoader: Section bpfloader_min_ver value is 2 [0x2]
[ 6.050401][ T510] printk: bpfloader: 594 output lines suppressed due to ratelimiting
[ 6.076813][ T204] init: Verified that /data/nfc has the encryption policy 20d5c94d237f8bd0122bdc2d700d0af8 v2 modes 1/4 flags 0xa
[ 6.077489][ T204] init: Verified that /data/nfc/param has the encryption policy 20d5c94d237f8bd0122bdc2d700d0af8 v2 modes 1/4 flags 0xa
[ 6.082357][ T204] file system registered
[ 6.093258][ T204] using random self ethernet address
[ 6.093293][ T204] using random host ethernet address
[ 6.098894][ T204] using random self ethernet address
[ 6.098924][ T204] using random host ethernet address
[ 6.286999][ T536] healthd: BatteryCycleCountPath not found
[ 6.287110][ T536] healthd: batteryStateOfHealthPath not found
[ 6.287122][ T536] healthd: batteryHealthStatusPath not found
[ 6.287136][ T536] healthd: batteryManufacturingDatePath not found
[ 6.287145][ T536] healthd: batteryFirstUsageDatePath not found
[ 6.287154][ T536] healthd: chargingStatePath not found
[ 6.287163][ T536] healthd: chargingPolicyPath not found
[ 6.296760][ T536] healthd: battery l=50 v=3300 t=2.6 h=2 st=3 c=-1600 fc=100 chg=au
I/TA: Hello Rockchip gatekeeper! ver:20230920 rpmb :0
[ 6.337156][ T561] watchdogd: watchdogd started (interval 10, margin 20)!
I/TA: Hello Rockchip Weaver! rpmb :0
上面这段是TEE TA的初始化log，只有打印Hello才表示TA部分正常运行，否则要检查TEE相关模块是否正常

[ 6.397617][ T542] bcmdhd: loading out-of-tree module taints kernel.
[ 6.427191][ T542] [dhd] _dhd_module_init: in Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240530-1)(d83d8d7)
[ 6.427191][ T542] /home/wlq/b1_Android14_29_aosp/external/wifi_driver/bcmdhd compiled on Jun 4 2024 at 10:06:56
[ 6.427191][ T542]
[ 6.427217][ T542] [dhd] ANDROID_VERSION = 14
[ 6.427223][ T542] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.36 (wlan=r892223-20231107-1)
[ 6.427383][ T542] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for index 0: 8212480(8020K)
[ 6.427392][ T542] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[ 6.427429][ T542] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=124, oob_irq_flags=0x4
[ 6.427438][ T542] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 6.427443][ T542] [dhd] dhd_wifi_platform_load: Enter
[ 6.427448][ T542] [dhd] wifi_platform_bus_enumerate device present 1
[ 6.427454][ T542] [dhd] ======== Card detection to detect PCIE card! ========
[ 6.427625][ T542] [dhd] dhdpcie_pci_probe : no mutex held
[ 6.427637][ T542] [dhd] dhdpcie_pci_probe : set mutex lock
[ 6.427642][ T542] [dhd] PCI_PROBE: bus 0x1, slot 0x0,vendor 0x14E4, device 0x449D(good PCI location)
[ 6.427649][ T542] [dhd] dhdpcie_init: found adapter info ‘DHD generic adapter’
[ 6.427655][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 3, size 139264
[ 6.427675][ T542] [dhd] succeed to alloc static buf
[ 6.427679][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 4, size 0
[ 6.427723][ T542] pcieh 0000:01:00.0: enabling device (0000 -> 0002)
[ 6.428123][ T542] [dhd] Disable CTO
[ 6.428930][ T542] [dhd] DHD: dongle ram size is set to 1310720(orig 1310720) at 0x170000
[ 6.428973][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 7, size 43904
[ 6.428990][ T542] [dhd] dhd_conf_set_chiprev : devid=0x449d, chip=0xaae8, chiprev=2, svid=0x14e4, ssid=0xaae8
[ 6.433782][ T542] [dhd] dhd_check_htput_chip: htput_support:1
[ 6.433801][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 0, size 5152
[ 6.434319][ T590] rkisp-vir0: rkisp_enum_frameintervals Not active sensor
[ 6.434582][ T590] rkisp-vir0: rkisp_enum_frameintervals Not active sensor
[ 6.435010][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 6.435034][ T590] rkcif_tools_id2: update sensor info failed -19
[ 6.435104][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 6.435114][ T590] stream_cif_mipi_id3: update sensor info failed -19
[ 6.442029][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 6.442071][ T590] stream_cif_mipi_id2: update sensor info failed -19
[ 6.442202][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 6.442212][ T590] rkcif_scale_ch3: update sensor info failed -19
[ 6.442256][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 6.442265][ T590] stream_cif_mipi_id0: update sensor info failed -19
[ 6.442311][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 6.442319][ T590] rkcif_scale_ch1: update sensor info failed -19
[ 6.450294][ T542] [dhd] dhd_ioctl_entry_local invalid parameter net 0000000000000000 dev_priv 0000000056970033
[ 6.450314][ T542] [dhd] CFG80211-ERROR) wl_is_fils_supported : FILS NOT supported, err -22
[ 6.451023][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 5, size 65536
[ 6.455324][ T542] [dhd] CFG80211-ERROR) wl_is_fils_supported : FILS NOT supported, err -19
[ 6.455458][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 19, size 65688
[ 6.455491][ T542] [dhd] dhd_log_dump_init: kernel log buf size = 512KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 76KB
[ 6.455499][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 15, size 4194304
[ 6.455998][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 16, size 8192
[ 6.456060][ T542] [dhd] mask:
[ 6.456068][ T542] [dhd] 0000: ff ff
[ 6.456074][ T542] [dhd] pattern:
[ 6.456078][ T542] [dhd] 0000: 88 8e
[ 6.456086][ T542] [dhd] mask:
[ 6.456091][ T542] [dhd] 0000: ff ff
[ 6.456095][ T542] [dhd] pattern:
[ 6.456100][ T542] [dhd] 0000: 08 06
[ 6.456108][ T542] [dhd] mask:
[ 6.456115][ T542] [dhd] 0000: ff ff ff 00 00 00 00 00 00 00 00 ff
[ 6.456119][ T542] [dhd] pattern:
[ 6.456125][ T542] [dhd] 0000: 08 00 45 00 00 00 00 00 00 00 00 01
[ 6.456135][ T542] [dhd] mask:
[ 6.456141][ T542] [dhd] 0000: ff ff f0 00 00 00 00 00 ff
[ 6.456145][ T542] [dhd] pattern:
[ 6.456151][ T542] [dhd] 0000: 86 dd 60 00 00 00 00 00 3a
[ 6.456164][ T542] [dhd] mask:
[ 6.456170][ T542] [dhd] 0000: ff ff ff 00 00 00 00 00 00 00 00 ff 00 00 00 00
[ 6.456176][ T542] [dhd] 0010: 00 00 00 00 00 00 ff ff ff ff
[ 6.456181][ T542] [dhd] pattern:
[ 6.456188][ T542] [dhd] 0000: 08 00 45 00 00 00 00 00 00 00 00 11 00 00 00 00
[ 6.456193][ T542] [dhd] 0010: 00 00 00 00 00 00 00 43 00 44
[ 6.456211][ T542] [dhd] mask:
[ 6.456217][ T542] [dhd] 0000: ff ff ff 00 00 00 00 00 00 00 00 ff 00 00 00 00
[ 6.456223][ T542] [dhd] 0010: 00 00 00 00 00 00 ff ff ff ff
[ 6.456227][ T542] [dhd] pattern:
[ 6.456234][ T542] [dhd] 0000: 08 00 45 00 00 00 00 00 00 00 00 11 00 00 00 00
[ 6.456240][ T542] [dhd] 0010: 00 00 00 00 00 00 00 44 00 43
[ 6.456245][ T542] [dhd] dhd_os_attach_pktlog(): dhd_os_attach_pktlog attach
[ 6.456278][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 6.456304][ T590] rkcif_scale_ch0: update sensor info failed -19
[ 6.456843][ T542] [dhd] dhd_attach(): thread:dhd_watchdog_thread:259 started
[ 6.456863][ T542] [dhd] dhd_deferred_work_init: work queue initialized
[ 6.456872][ T542] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 3
[ 6.456878][ T542] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[ 6.456894][ T542] [dhd] dhd_cpumasks_init CPU masks primary(big)=0xf0 secondary(little)=0xe
[ 6.456924][ T22] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.456967][ T23] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457002][ T29] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457039][ T35] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457069][ T41] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457152][ T48] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457184][ T54] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457369][ T60] [dhd] dhd_cpu_startup_callback(): LB data is not initialized yet.
[ 6.457450][ T542] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[ 6.457462][ T542] [dhd] dhdpcie_bus_attach: making DHD_BUS_DOWN
[ 6.457471][ T542] [dhd] dhdpcie_init: rc_dev from dev->bus->self (1d87:3576) is 0000000000000000
[ 6.457616][ T542] [dhd] dhdpcie_init: rc_ep_aspm_cap: 1 rc_ep_l1ss_cap: 1
[ 6.457649][ T542] [dhd] dhdpcie_request_irq: INTx enabled, irq=69
[ 6.457681][ T542] [dhd] dhd_bus_download_firmware: firmware path=fw_bcmdhd.bin, nvram path=nvram.txt
[ 6.457711][ T542] [dhd] dhd_conf_set_path_params : Final fw_path=/fw_bcm43752a2_pcie_ag.bin
[ 6.457718][ T542] [dhd] dhd_conf_set_path_params : Final nv_path=/nvram_ap6275p.txt
[ 6.457723][ T542] [dhd] dhd_conf_set_path_params : Final clm_path=/clm_bcm43752a2_pcie_ag.blob
[ 6.457728][ T542] [dhd] dhd_conf_set_path_params : Final conf_path=/config.txt
[ 6.458137][ T542] pcieh 0000:01:00.0: Direct firmware load for /config.txt failed with error -2
[ 6.458157][ T542] [dhd] dhd_os_get_img_fwreq: request_firmware /config.txt err: -2
[ 6.458167][ T542] [dhd] dhd_os_get_img(Request Firmware API) error : -30
[ 6.458173][ T542] [dhd] dhd_conf_read_config : Ignore config file /config.txt
[ 6.458180][ T542] [dhd] d2h_intr_method -> PCIE_INTX(0); d2h_intr_control -> D2H_INTMASK(0)
[ 6.458287][ T542] [dhd] dhdpcie_download_code_file: dhd_tcm_test_enable 0, dhd_tcm_test_status 0, dhd_tcm_test_mode 2
[ 6.458295][ T542] [dhd] dhdpcie_download_code_file: download firmware /fw_bcm43752a2_pcie_ag.bin
[ 6.460700][ T542] [dhd] dhd_os_get_img_fwreq: /fw_bcm43752a2_pcie_ag.bin (940225 bytes) open success
[ 6.464610][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 6.464638][ T590] rkcif_scale_ch2: update sensor info failed -19
[ 6.464705][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 6.464715][ T590] rkcif_tools_id0: update sensor info failed -19
[ 6.464761][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 6.464770][ T590] rkcif_tools_id1: update sensor info failed -19
[ 6.464819][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 6.464828][ T590] stream_cif_mipi_id1: update sensor info failed -19
[ 6.564067][ T542] [dhd] dhd_os_get_img_fwreq: /nvram_ap6275p.txt (7458 bytes) open success
[ 6.564140][ T542] [dhd] # AP6275P_NVRAM_V1.3_20230109A
[ 6.582731][ T542] [dhd] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 6.582752][ T542] [dhd] dhdpcie_bus_write_vars: New varsize is 6040, length token(nvram_csm)=0xfa1905e6
[ 6.583185][ T542] [dhd] Download and compare of TLV 0xfeedc0de succeeded (size 128, addr 2ae7dc).
[ 6.583325][ T542] [dhd] dhdpcie_bus_download_state: Took ARM out of Reset
[ 6.675885][ T542] [dhd] dhdpcie_readshared: addr=0x20c0f4 nvram_csm=0xfa1905e6
[ 6.675930][ T542] [dhd] ### Total time ARM OOR to Readshared pass took 92660 usec ###
[ 6.675941][ T542] [dhd] dhdpcie_readshared: PCIe shared addr (0x0020c0f4) read took 90000 usec before dongle is ready
[ 6.676903][ T542] [dhd] FW supports DAR ? N
[ 6.677183][ T542] [dhd] dhdpcie_readshared: max H2D queues 64
[ 6.677192][ T542] [dhd] FW supports MD ring ? N
[ 6.677226][ T542] [dhd] dhd_bus_init: Enabling bus->intr_enabled
[ 6.677234][ T542] [dhd] dhdpcie_oob_intr_register OOB irq=124 flags=0x4
[ 6.677277][ T542] [dhd] dhdpcie_oob_intr_register: enable_irq_wake
[ 6.677321][ T542] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 9, size 32896
[ 6.677337][ T542] [dhd] dhd_prot_init:4146: h2d_max_txpost = 512
[ 6.677345][ T542] [dhd] dhd_prot_init:4152: h2d_htput_max_txpost = 2048
[ 6.677469][ T542] [dhd] dhd_prot_init: max_rxbufpost:511 rx_buf_burst:64 rx_bufpost_threshold:64
[ 6.677477][ T542] [dhd] ENABLING DW:0
[ 6.677507][ T542] [dhd] dhd_prot_d2h_sync_init(): D2H sync mechanism is XORCSUM
[ 6.677527][ T542] [dhd] dhd_bus_hostready : Read PCICMD Reg: 0x00100006
[ 6.677706][ T542] [dhd] dhd_bus_hostready: Ring Hostready:1
[ 6.677715][ T542] [dhd] Attach flowrings pool for 64 rings
[ 6.678041][ T542] [dhd] trying to send create d2h info ring: id 70
[ 6.678053][ T542] [dhd] dhd_send_d2h_ringcreate ringid: 3 idx: 70 max_h2d: 67
[ 6.678979][ C0] [dhd] dhd_prot_process_d2h_ring_create_complete ring create Response status = 0 ring 3, id 0xfffc
[ 6.679020][ C0] [dhd] info buffer post after ring create
[ 6.680903][ T542] [dhd] wlc_ver_major 12, wlc_ver_minor 1
[ 6.680919][ T542] [dhd] dhd_get_memdump_info: MEMDUMP ENABLED = 3
[ 6.682360][ T542] [dhd] dhd_sync_with_dongle: GET_REVINFO device 0x449d, vendor 0x14e4, chipnum 0xaae8
[ 6.683858][ T542] [dhd] dhd_sync_with_dongle: RxBuf Post : 2048
[ 6.683874][ T542] [dhd] dhd_sync_with_dongle: RxBuf Post Alloc : 2048
[ 6.687286][ T542] [dhd] dhd_preinit_ioctls: preinit_status IOVAR not supported, use legacy preinit
[ 6.687301][ T542] [dhd] dhd_tcpack_suppress_set 378: already set to 3
[ 6.690253][ T542] [dhd] dhd_legacy_preinit_ioctls: hostwake_oob enabled
[ 6.691852][ T542] [dhd] dhd_legacy_preinit_ioctls: use firmware generated mac_address d4:9c:dd:f6:9c:74
[ 6.692628][ T542] [dhd] dhd_os_get_img_fwreq: /clm_bcm43752a2_pcie_ag.blob (32297 bytes) open success
[ 6.695006][ T542] [dhd] dhd_check_current_clm_data: ----- This FW is not included CLM data -----
[ 6.740564][ T542] [dhd] dhd_apply_default_clm: CLM download succeeded
[ 6.742089][ T542] [dhd] dhd_check_current_clm_data: ----- This FW is included CLM data -----
[ 6.748335][ T542] [dhd] Firmware up: op_mode=0x0005, MAC=d4:9c:dd:f6:9c:74
[ 6.769414][ T542] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 26 ret: 0
[ 6.789522][ T542] [dhd] arp_enable:1 arp_ol:0
[ 6.810099][ T542] [dhd] Driver: 101.10.591.52.27 (20240409-1)(20240530-1)
[ 6.810099][ T542] [dhd] Firmware: wl0: Sep 20 2023 17:20:09 version 18.35.387.23.206 (g711dd630) FWID 01-c17ee42e
[ 6.810099][ T542] [dhd] CLM: 9.9.20_SS (2022-11-21 17:26:58)
[ 6.812845][ T542] [dhd] dhd_pno_init: Support Android Location Service
[ 6.814371][ T542] [dhd] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
[ 6.814422][ T542] [dhd] dhd_rtt_init : FTM is not supported
[ 6.814436][ T542] [dhd] dhd_rtt_init EXIT, err = 0
[ 6.891942][ T542] [dhd] dhd_legacy_preinit_ioctls: d3_hostwake_delay IOVAR not present, proceed
[ 6.923286][ C0] [dhd] dhd_update_interface_flow_info: ifindex:0 previous role:0 new role:0
[ 6.923333][ C0] [dhd] dhd_rx_frame: net device is NOT registered. drop event packet
[ 6.927192][ T542] [dhd] dhd_conf_set_country : set country CN, revision 0
[ 6.932706][ T542] [dhd] dhd_conf_set_country : Country code: CN (CN/0)
[ 6.944292][ T542] [dhd] Dongle Host Driver, version 101.10.591.52.27 (20240409-1)(20240530-1)(d83d8d7)
[ 6.944292][ T542] /home/wlq/b1_Android14_29_aosp/external/wifi_driver/bcmdhd compiled on Jun 4 2024 at 10:06:56
[ 6.944292][ T542]
[ 6.949748][ T542] [dhd] Register interface [wlan0] MAC: d4:9c:dd:f6:9c:74
[ 6.949748][ T542]
[ 6.949927][ T542] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 3 -> mode 0
[ 6.949950][ T542] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=40, TCPDATA_INFO_MAXNUM=40
[ 6.949968][ T542] [dhd] [wlan0] wl_android_wifi_off : g_wifi_on=1 force_off=1
[ 6.949991][ T542] [dhd] dhd_bus_devreset: == Power OFF ==
[ 6.950002][ T542] [dhd] dhdpcie_advertise_bus_cleanup: DB7 Not sent!!!
[ 6.950035][ T542] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
[ 6.950183][ T542] [dhd] dhd_dpc_kill: tasklet disabled
[ 6.952766][ T542] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
[ 6.952801][ T542] [dhd] dhd_bus_devreset: WLAN OFF Done
[ 6.952814][ T542] [dhd] wifi_platform_set_power = 0, delay: 10 msec
[ 6.952824][ T542] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
[ 6.952831][ T542] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 6.952838][ T542] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 6.952845][ T542] wifi power off
[ 6.977566][ T675] read descriptors
[ 6.977633][ T675] read strings
[ 7.057583][ T542] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 7.057605][ T542] [WLAN_RFKILL]: wifi shut off power [GPIO54-0]
[ 7.068628][ T542] [dhd] wifi_platform_set_power = 0, sleep done: 10 msec
[ 7.068651][ T542] [dhd] [wlan0] wl_android_wifi_off : out
[ 7.068659][ T542] [dhd] wl_android_post_init: 0
[ 7.068667][ T542] [dhd] dhdpcie_pci_probe : mutex is released.
[ 7.068797][ T542] [dhd] _dhd_module_init: Exit err=0
[ 7.395128][ T677] dwc3 23000000.usb: device reset
[ 7.475202][ T174] android_work: sent uevent USB_STATE=CONNECTED
[ 7.478870][ T677] dwc3 23000000.usb: device reset
[ 7.590806][ T174] android_work: sent uevent USB_STATE=CONFIGURED
[ 9.300323][ T274] servicemanager: Notifying apexservice they do (previously: don’t) have clients when service is guaranteed to be in use
[ 9.332134][ T274] servicemanager: Could not find android.hardware.power.stats.IPowerStats/default in the VINTF manifest.
[ 9.335051][ T274] servicemanager: Found android.frameworks.stats.IStats/default in framework VINTF manifest.
[ 9.335381][ T274] servicemanager: Could not find android.hardware.memtrack.IMemtrack/default in the VINTF manifest.
[ 9.399484][ T289] type=1400 audit(1717467515.280:542): avc: denied { read } for comm=“binder:306_5” name=“wakeup4” dev=“sysfs” ino=36238 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:s0 t1
[ 9.399586][ T289] type=1400 audit(1717467515.280:543): avc: denied { open } for comm=“binder:306_5” path=“/sys/devices/platform/2ac50000.i2c/i2c-2/2-0051/rtc/rtc0/alarmtimer.4.auto/wakeup/wakeup4” d1
[ 9.399637][ T289] type=1400 audit(1717467515.280:544): avc: denied { read } for comm=“binder:306_5” name=“event_count” dev=“sysfs” ino=36245 scontext=u:r:system_suspend:s0 tcontext=u:object_r:sysfs:1
[ 9.399680][ T289] type=1400 audit(1717467515.280:545): avc: denied { open } for comm=“binder:306_5” path=“/sys/devices/platform/2ac50000.i2c/i2c-2/2-0051/rtc/rtc0/alarmtimer.4.auto/wakeup/wakeup4/ev1
[ 9.399722][ T289] type=1400 audit(1717467515.280:546): avc: denied { getattr } for comm=“binder:306_5” path=”/sys/devices/platform/2ac50000.i2c/i2c-2/2-0051/rtc/rtc0/alarmtimer.4.auto/wakeup/wakeup41
[ 9.456439][ T274] servicemanager: Found android.hardware.power.IPower/default in device VINTF manifest.
[ 9.463409][ T274] servicemanager: Found android.hardware.light.ILights/default in device VINTF manifest.
[ 9.917758][ T86] Freeing drm_logo memory: 1384K
[ 11.098100][ T1] init: service ‘idmap2d’ requested start, but it is already running (flags: 4)
[ 11.098132][ T1] init: Control message: Processed ctl.start for ‘idmap2d’ from pid: 690 (system_server)
[ 11.154986][ T274] servicemanager: Found android.hardware.sensors.ISensors/default in device VINTF manifest.
[ 11.158524][ T274] servicemanager: Found android.hardware.health.IHealth/default in device VINTF manifest.
[ 11.162335][ T536] healthd: battery l=50 v=3300 t=2.6 h=2 st=3 c=-1600 fc=100 chg=au
[ 11.288312][ T274] servicemanager: Could not find android.hardware.vibrator.IVibratorManager/default in the VINTF manifest.
[ 11.288519][ T274] servicemanager: Could not find android.hardware.vibrator.IVibrator/default in the VINTF manifest.
[ 11.390853][ T289] type=1400 audit(1717467517.272:547): avc: denied { read } for comm=“android.ui” name=“name” dev=“sysfs” ino=24924 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs:s0 tclass=1
[ 11.390932][ T289] type=1400 audit(1717467517.272:548): avc: denied { open } for comm=“android.ui” path=“/sys/devices/platform/2602e000.syscon/2602e000.syscon:usb2-phy@2000/extcon/extcon1/cable.3/nam1
[ 11.390973][ T289] type=1400 audit(1717467517.272:549): avc: denied { getattr } for comm=“android.ui” path=”/sys/devices/platform/2602e000.syscon/2602e000.syscon:usb2-phy@2000/extcon/extcon1/cable.3/1
[ 11.486243][ T1] init: processing action (sys.sysctl.extra_free_kbytes=*) from (/system/etc/init/hw/init.rc:1233)
[ 11.486898][ T1] init: starting service ‘exec 16 (/system/bin/extra_free_kbytes.sh 24300)’…
[ 11.490680][ T1] init: … started service ‘exec 16 (/system/bin/extra_free_kbytes.sh 24300)’ has pid 807
[ 11.490760][ T1] init: SVC_EXEC service ‘exec 16 (/system/bin/extra_free_kbytes.sh 24300)’ pid 807 (uid 0 gid 0+0 context default) started; waiting…
[ 11.720325][ T1] init: Service ‘exec 16 (/system/bin/extra_free_kbytes.sh 24300)’ (pid 807) exited with status 0 waiting took 0.231000 seconds
[ 11.720362][ T1] init: Sending signal 9 to service ‘exec 16 (/system/bin/extra_free_kbytes.sh 24300)’ (pid 807) process group…
[ 11.720480][ T1] libprocessgroup: Successfully killed process cgroup uid 0 pid 807 in 0ms
[ 11.945074][ T760] read descriptors
[ 11.945111][ T760] read strings
[ 11.945215][ T760] read descriptors
[ 11.945225][ T760] read strings
[ 12.114897][ T560] gsensor_icm4260x 7-0068: set sensor poll time to 200ms
[ 12.116620][ T560] gsensor_icm4260x 7-0068: sensor on: starting poll sensor data 196ms
[ 12.215250][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 12.216173][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: PHY [stmmac-0:01] driver [Generic PHY] (irq=POLL)
[ 12.216728][ T583] dwmac4: Master AXI performs any burst length
[ 12.216769][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: No Safety Features support found
[ 12.216796][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 12.217390][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: registered PTP clock
[ 12.222348][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: FPE workqueue start
[ 12.222371][ T583] rk_gmac-dwmac 2a220000.ethernet eth0: configuring for phy/rgmii-rxid link mode
[ 12.229086][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 12.229884][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: PHY [stmmac-1:01] driver [Generic PHY] (irq=POLL)
[ 12.230435][ T583] dwmac4: Master AXI performs any burst length
[ 12.230474][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: No Safety Features support found
[ 12.230508][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 12.230856][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: registered PTP clock
[ 12.232200][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: FPE workqueue start
[ 12.232220][ T583] rk_gmac-dwmac 2a230000.ethernet eth1: configuring for phy/rgmii-rxid link mode
[ 12.296743][ T494] apexd: getSessions() received by ApexService
[ 12.999658][ T289] type=1400 audit(1717467518.880:550): avc: granted { read } for comm=“rkstack.process” name=“psched” dev=“proc” ino=4026532026 scontext=u:r:network_stack:s0 tcontext=u:object_r:proce
[ 12.999774][ T289] type=1400 audit(1717467518.880:551): avc: granted { read open } for comm=“rkstack.process” path=“/proc/970/net/psched” dev=“proc” ino=4026532026 scontext=u:r:network_stack:s0 tconte
[ 13.453086][ T554] [BT_RFKILL]: bt shut off power
[ 13.453355][ T554] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
[ 13.505783][ T554] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
[ 13.505864][ T554] [BT_RFKILL]: ENABLE UART_RTS
[ 13.613710][ T554] [BT_RFKILL]: DISABLE UART_RTS
[ 13.613743][ T554] [BT_RFKILL]: bt turn on power
[ 13.613865][ T554] [BT_RFKILL]: Request irq for bt wakeup host
[ 13.614083][ T554] [BT_RFKILL]: ** disable irq
[ 13.614375][ T554] of_dma_request_slave_channel: dma-names property of node ‘/serial@2ad70000’ missing or empty
[ 13.614398][ T554] dw-apb-uart 2ad70000.serial: failed to request DMA, use interrupt mode
[ 13.806332][ T494] AidlLazyServiceRegistrar: Process has 0 (of 1 available) client(s) in use after notification apexservice has clients: 0
[ 13.806375][ T494] AidlLazyServiceRegistrar: Shutdown prevented by forcePersist override flag.
[ 14.712383][ T560] gsensor_icm4260x 7-0068: set sensor poll time to 66ms
[ 14.802417][ T44] binder: undelivered transaction 25406, process died.
[ 14.802942][ T1] init: Service ‘bootanim’ (pid 315) exited with status 0 oneshot service took 10.767000 seconds in background
到这里表示Android动画结束，开机进入Android Launch界面，Android启动完成，[ 14.802942]是整个Android开机的完成耗时14.8秒
[ 14.854615][ T274] servicemanager: Found android.hardware.wifi.IWifi/default in device VINTF manifest.
[ 14.858929][ T274] servicemanager: Found android.hardware.wifi.IWifi/default in device VINTF manifest.
[ 14.860561][ T274] servicemanager: Found android.hardware.wifi.IWifi/default in device VINTF manifest.
[ 14.861175][ T274] servicemanager: Found android.hardware.wifi.IWifi/default in device VINTF manifest.
[ 14.868565][ T274] servicemanager: Notifying apexservice they do (previously: don’t) have clients when service is guaranteed to be in use
[ 14.868750][ T494] AidlLazyServiceRegistrar: Process has 1 (of 1 available) client(s) in use after notification apexservice has clients: 1
[ 14.868774][ T494] AidlLazyServiceRegistrar: Shutdown prevented by forcePersist override flag.
[ 14.869080][ T494] apexd: markBootCompleted() received by ApexService
[ 14.883511][ T274] servicemanager: Found android.hardware.weaver.IWeaver/default in device VINTF manifest.
[ 14.903928][ T289] type=1400 audit(1717467520.784:558): avc: denied { create } for comm=“init” name=“vehicle” scontext=u:r:vendor_init:s0 tcontext=u:object_r:device:s0 tclass=file permissive=1
[ 14.904019][ T289] type=1400 audit(1717467520.784:559): avc: denied { write } for comm=“init” path=“/dev/vehicle” dev=“tmpfs” ino=743 scontext=u:r:vendor_init:s0 tcontext=u:object_r:device:s0 tclass=1
[ 14.906729][ T590] rkisp-vir0: rkisp_enum_frameintervals Not active sensor
[ 14.906945][ T590] rkisp-vir0: rkisp_enum_frameintervals Not active sensor
[ 14.907238][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 14.907253][ T590] rkcif_tools_id2: update sensor info failed -19
[ 14.907315][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 14.907325][ T590] stream_cif_mipi_id3: update sensor info failed -19
[ 14.913846][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 14.913919][ T590] stream_cif_mipi_id2: update sensor info failed -19
[ 14.914071][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 14.914086][ T590] rkcif_scale_ch3: update sensor info failed -19
[ 14.914138][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 14.914148][ T590] stream_cif_mipi_id0: update sensor info failed -19
[ 14.914194][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 14.914202][ T590] rkcif_scale_ch1: update sensor info failed -19
[ 14.926415][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 14.926436][ T590] rkcif_scale_ch0: update sensor info failed -19
[ 14.934641][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 14.934665][ T590] rkcif_scale_ch2: update sensor info failed -19
[ 14.934713][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 14.934721][ T590] rkcif_tools_id0: update sensor info failed -19
[ 14.934760][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 14.934767][ T590] rkcif_tools_id1: update sensor info failed -19
[ 14.934805][ T590] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 14.934813][ T590] stream_cif_mipi_id1: update sensor info failed -19
[ 15.044502][ T1] zram0: detected capacity change from 0 to 3991448
[ 15.069709][ T1] mkswap: Swapspace size: 1995720k, UUID=fd7b99a4-b336-4cb2-938c-974c35e0fa74
[ 15.071423][ T1] Adding 1995720k swap on /dev/block/zram0. Priority:-2 extents:1 across:1995720k SS
[ 15.120201][ T494] apexd: destroyCeSnapshotsNotSpecified() received by ApexService user_id : 0 retain_rollback_ids : []
[ 15.130133][ T375] apexd: Deleting unused dm device com.android.apex.cts.shim
[ 15.130379][ T375] apexd: Didn’t generate uevent for [com.android.apex.cts.shim] removal
[ 15.130408][ T375] apexd: Failed to delete dm-device com.android.apex.cts.shim
[ 15.351929][ T274] servicemanager: Found android.hardware.graphics.allocator.IAllocator/default in device VINTF manifest.
[ 15.356263][ T274] servicemanager: Found android.hardware.graphics.allocator.IAllocator/default in device VINTF manifest.
[ 15.498503][ T289] type=1400 audit(1717467521.380:560): avc: denied { read } for comm=“HwBinder:537_3” name=“u:object_r:default_prop:s0” dev=“tmpfs” ino=139 scontext=u:r:mediacodec:s0 tcontext=u:obje1
[ 15.498633][ T289] type=1400 audit(1717467521.380:561): avc: denied { open } for comm=“HwBinder:537_3” path=“/dev/properties/u:object_r:default_prop:s0” dev=“tmpfs” ino=139 scontext=u:r:mediacode1
[ 15.498699][ T289] type=1400 audit(1717467521.380:562): avc: denied { getattr } for comm=“HwBinder:537_3” path=“/dev/properties/u:object_r:default_prop:s0” dev=“tmpfs” ino=139 scontext=u:r:mediac1
[ 15.498751][ T289] type=1400 audit(1717467521.380:563): avc: denied { map } for comm=“HwBinder:537_3” path=“/dev/properties/u:object_r:default_prop:s0” dev=“tmpfs” ino=139 scontext=u:r:mediacodec1
[ 15.547184][ T274] servicemanager: Found android.hardware.graphics.allocator.IAllocator/default in device VINTF manifest.
[ 15.550665][ T274] servicemanager: Found android.hardware.graphics.allocator.IAllocator/default in device VINTF manifest.
[ 15.622709][ T554] [BT_RFKILL]: bt shut off power
[ 15.636088][ T289] type=1400 audit(1717467521.516:564): avc: denied { read } for comm=“PowerManagerSer” name=“u:object_r:vendor_default_prop:s0” dev=“tmpfs” ino=333 scontext=u:r:system_server:s0 tcon1
[ 15.636199][ T289] type=1400 audit(1717467521.516:565): avc: denied { open } for comm=“PowerManagerSer” path=“/dev/properties/u:object_r:vendor_default_prop:s0” dev=“tmpfs” ino=333 scontext=u:r:s1
[ 15.636259][ T289] type=1400 audit(1717467521.516:566): avc: denied { getattr } for comm=“PowerManagerSer” path=“/dev/properties/u:object_r:vendor_default_prop:s0” dev=“tmpfs” ino=333 scontext=u:1
[ 15.636306][ T289] type=1400 audit(1717467521.516:567): avc: denied { map } for comm=“PowerManagerSer” path=“/dev/properties/u:object_r:vendor_default_prop:s0” dev=“tmpfs” ino=333 scontext=u:r:sy1
[ 15.880414][ T1706] audit_log_lost: 319 callbacks suppressed
[ 15.880424][ T1706] audit: audit_lost=107 audit_rate_limit=5 audit_backlog_limit=64
[ 15.880461][ T1706] audit: rate limit exceeded
[ 15.994232][ T560] gsensor_icm4260x 7-0068: set sensor poll time to 200ms
[ 15.999912][ T8] <>[gt1x_suspend:2179] Suspend start…
[ 15.999953][ T8] <>[gt1x_enter_sleep:925] Enter sleep mode by poweroff
[ 16.065607][ T8] <>[gt1x_suspend:2232] Suspend end…
[ 16.098910][ T313] rockchip-vop2 27d00000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp1
[ 17.812891][ T1025] audit: audit_lost=116 audit_rate_limit=5 audit_backlog_limit=64
[ 17.813011][ T1025] audit: rate limit exceeded
[ 18.806682][ T375] AidlLazyServiceRegistrar: Process has 0 (of 1 available) client(s) in use after notification apexservice has clients: 0
[ 18.806771][ T375] AidlLazyServiceRegistrar: Trying to shut down the service. No clients in use for any service in process.
[ 18.807877][ T375] AidlLazyServiceRegistrar: Unregistered all clients and exiting
[ 18.815112][ T494] printk: binder:375_2: 146 output lines suppressed due to ratelimiting
[ 18.816122][ T1] init: Service ‘apexd’ (pid 375) exited with status 0 oneshot service took 14.042000 seconds in background
[ 18.816235][ T1] init: Sending signal 9 to service ‘apexd’ (pid 375) process group…
[ 18.816740][ T1] libprocessgroup: Successfully killed process cgroup uid 0 pid 375 in 0ms
[ 22.722771][ T1] init: Sending signal 9 to service ‘idmap2d’ (pid 619) process group…
[ 22.728748][ T1] libprocessgroup: Successfully killed process cgroup uid 1000 pid 619 in 5ms
[ 22.729981][ T1] init: Control message: Processed ctl.stop for ‘idmap2d’ from pid: 690 (system_server)
[ 22.730471][ T1] init: Service ‘idmap2d’ (pid 619) received signal 9
[ 27.769321][ T1] init: starting service ‘simple_bugreportd’…
[ 27.770546][ T1] init: Created socket ‘/dev/socket/dumpstate’, mode 660, user 2000, group 1007
[ 27.780297][ T1] init: … started service ‘simple_bugreportd’ has pid 2002
[ 27.780426][ T1] init: Control message: Processed ctl.start for ‘simple_bugreportd’ from pid: 690 (system_server)
[ 27.872744][ T282] logd: logdr: UID=0 GID=0 PID=2005 n tail=0 logMask=99 pid=0 start=0ns deadline=0ns
[ 28.093342][ T282] logd: logdr: UID=0 GID=0 PID=2007 n tail=0 logMask=4 pid=0 start=0ns deadline=0ns
[ 28.182743][ T289] type=1400 audit(1717467534.064:584): avc: denied { read } for comm=“dumpstate” name=“summary” dev=“debugfs” ino=13523 scontext=u:r:dumpstate:s0 tcontext=u:object_r:debugfs:s0 tclas1
[ 28.183009][ T289] type=1400 audit(1717467534.064:585): avc: denied { open } for comm=“dumpstate” path=“/sys/kernel/debug/dri/0/summary” dev=“debugfs” ino=13523 scontext=u:r:dumpstate:s0 tcontext=u:o1
[ 28.258477][ T289] type=1400 audit(1717467534.140:586): avc: denied { search } for comm=“mount” name=“pass_through” dev=“tmpfs” ino=16 scontext=u:r:dumpstate:s0 tcontext=u:object_r:mnt_pass_through_f1
[ 28.258698][ T289] type=1400 audit(1717467534.140:587): avc: denied { getattr } for comm=“mount” path=“/mnt/pass_through/0/emulated” dev=“dm-40” ino=130 scontext=u:r:dumpstate:s0 tcontext=u:object_r:1
[ 29.963254][ T1] init: Service ‘simple_bugreportd’ (pid 2002) exited with status 0 oneshot service took 2.187000 seconds in background
[ 29.963308][ T1] init: Sending signal 9 to service ‘simple_bugreportd’ (pid 2002) process group…
[ 29.963526][ T1] libprocessgroup: Successfully killed process cgroup uid 0 pid 2002 in 0ms